Comtech EF Data SDM-2020 Скачать руководство пользователя | Manualshive

Страница: 125 / 215

background image

Data Interfaces

SDM-2020 Satellite Demodulator

A–24

Rev.3

Notes:

1.

In loopback TX, data is routed through as much of the interface card as
practicable before being returned to the RX interface.

In a modulator chassis, TX

data continues to enter the modulator and is transmitted during loopback. In the
demodulator, satellite data is interrupted during loopback and the data entering
the TX connector is returned to the RX connector. Demodulator data from the
satellite is not routed to the modulator by the data interface.

2.

Loop-Through Mode (Modulator Only); is the same as loopback only the yellow
TEST MODE LED is not activated.

3. Rev. A or later assemblies include this capability. Rev dash (-) assemblies can be

upgraded to this capability.

A.4.3 User

Interfaces

The following paragraphs describe the electrical and physical properties of the ASI/RS-
422 data interface module.

A.4.3.1

Transmit Input Connectors, J3/J4, BNC, Female

These two connectors accept TX data from the terrestrial interface. By default, J3 is
enabled and J4 is disabled. The active input is user programmable and maintained in non-
volatile memory of the modulator or demodulator chassis. Both connectors are terminated
into 75

Ω

, whether selected or not.

A.4.3.2 RS-422

Connector, J5, 25-Pin D, Female

This connector is compatible with EIA-530 operation and pin-out. It is a serial interface
with RS-422 signals plus the TTL-OC fault signals indicating the status of the modulator
or demodulator.

A.4.3.2.1

Connector Pinout, J5

The connector is a 25-pin, female, D type, with threaded jack nuts (refer to Table A-12
for connector pinout).

Notes:

1.

RS-422 signal levels are as defined in RS-422.

2.

The differential sense of all signal pairs is a logic “1” when “A” is negative with
respect to “B.”

«
...
123
124
125
126
127
...
»

Содержание SDM-2020
























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SDM-2020

Бренд: TA Страницы: 66

Бренд: LEXIBOOK Страницы: 29

Бренд: LEXIBOOK Страницы: 31

Бренд: Bowmar Страницы: 9

Бренд: PR electronics Страницы: 18

Бренд: Casio Страницы: 25

Бренд: Casio Страницы: 204

Бренд: DRAKE Страницы: 10

Бренд: Metro Modular Страницы: 2

UFOcompact plus 878

Бренд: Kathrein Страницы: 20

Бренд: Jiggery-Pokery Страницы: 14

Бренд: ABB Страницы: 10

ConstructionMaster HeavyCalc 4320

Бренд: Calculated Industries Страницы: 51

Бренд: Texas Instruments Страницы: 148

Бренд: Texas Instruments Страницы: 422

Бренд: Texas Instruments Страницы: 696

Бренд: Rebell Страницы: 62

Бренд: Rebell Страницы: 86

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды