Comtech EF Data SDM-2020 Скачать руководство пользователя

Страница: 142 / 215

SDM-2020 Satellite Demodulator

Data Interfaces

Rev.3

A–41

A.6

G.703 Data Interface

The following paragraphs describe the G.703 data interface.

A.6.1 Applicable

Documents

Applicable documents, as referenced herein, include:

•

ITU-T G.703, Physical/Electrical Characteristics Of Hierarchical Digital
Interfaces

•

ITU -T G.704, Synchronous Frame Structures Used At Primary And Secondary
Hierarchical Levels

•

ITU-T G.742, General Considerations On Second Order Multiplex Equipment

•

ITU-T G.743, Second Order Digital Multiplex Equipment Operating At
6312 kbit/s And Using Positive Justification

•

ITU-T G.745, Second Order Digital Multiplex Equipment Operating At
8448 kbit/s And Using Positive/Zero/Negative Justification

•

ITU-T G.747, Second Order Digital Multiplex Equipment Operating At
6312 kbit/s And Multiplexing Three Tributaries At 2048 kbit/s

•

ITU-T G.751, Digital Multiplex Equipments Operating At The Third Order Bit
Rate Of 34,368 kbit/s And The Fourth Order Bit Rate Of 139,264 kbit/s And
Using Positive Justification

•

ITU-T G.752, Characteristics of Digital Multiplex Equipments Based On A
Second Order Bit Rate Of 6312 kbit/s And Using Positive Justification

•

ITU-T G.753, Third Order Digital Multiplex Equipment Operating At
34,368 kbit/s And Using Positive/Zero/Negative Justification

•

ITU-T G.823, The Control Of Jitter And Wander Within Digital Networks Which
Are Based On The 2048 kbit/s Hierarchy

•

ITU-T G.824, The Control Of Jitter And Wander Within Digital Networks Which
Are Based On The 1544 kbit/s Hierarchy

•

Bellcore SONET STS-1

Содержание SDM-2020
























































































































































































































Результаты поиска

Содержание SDM-2020

Отзывы:

Похожие инструкции для SDM-2020

Бренды по названию

Популярные бренды

Comtech EF Data SDM-2020, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SDM-2020

Отзывы:

Похожие инструкции для SDM-2020

Бренды по названию

Популярные бренды