ComAp IM-NT Скачать руководство пользователя | Manualshive

Страница: 75 / 328

background image

InteliMains

NT

, SW version 3.0

InteliMains-NT-BTB-3.0-Reference Guide.pdf,

©ComAp – June 2013

75

8.1.6.1

Configured protections by default

BusL Voltage Unbalance:

This protection is by default configured as HistRecOnly with indication

“BusL V unbal”. For more information on this protection see the Protections tab in default
archive.

BusL Current Unbalance:

This protection is by default configured as HistRecOnly with indication

“BusL I unbal”. For more information on this protection see the Protections tab in default
archive.

BusR Voltage Unbalance:

This protection is by default configured as HistoryRecOnly with indication

“BusR U unbal”. For more information on this protection see the Protections tab in default
archive.

Battery Over and Under Voltage:

There are two protections configured by default as Warnings with

indication “Batt volt”. For more information on this protection see the Protections tab in default
archive.

8.1.6.2

Configuration of User configurable protections in GenConfig

It is possible to configure protections on Binary Input, Analog Input or any value that is available in the
controller.

H

INT

Since there can be number of protections configured by the user it is possible to prepare more
complex reaction of the Feeder to the state of the voltage on Bus. It is possible to add reaction on over
and under frequency, over and under voltage and other parameters. These protection will be working
along with the fixed protections.

8.1.6.2.1 Binary Input protection configuration

Open I/O tab in GenCofig and adjust parameters that are described below.

Enable/Disable protection for this input

Name of the binary input is also

used as the name of the protection

Type of protection

Toggle normally closed/normally open

Defines when the protection is active

Defines protection delay

8.1.6.2.2 Analog Input protection configuration

Open I/O tab in GenCofig and adjust parameters that are described below.

«
...
73
74
75
76
77
...
»

Содержание IM-NT









































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IM-NT

Бренд: Yardney Страницы: 8

Бренд: Badger Basket Страницы: 3

Бренд: BADLANDS Страницы: 2

Бренд: D+H Страницы: 14

Бренд: Samson Страницы: 48

Бренд: Vacon Страницы: 50

Бренд: V2 Страницы: 116

Бренд: V2 Страницы: 8

Бренд: V2 Страницы: 25

Бренд: V2 Страницы: 124

Бренд: Zodiac Страницы: 12

Бренд: National Instruments Страницы: 34

Бренд: Parker Страницы: 54

Бренд: RAM Страницы: 71

XP-9 88-IoT Series

Бренд: ICP DAS USA Страницы: 8

Бренд: ICON Страницы: 2

Бренд: ICP DAS USA Страницы: 4

963325-0403 - RumblePad 2 Vibration Feedback Gamepad Game Pad

Бренд: Logitech Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды