ComAp IM-NT Скачать руководство пользователя

Страница: 164 / 328

InteliMains

, SW version 3.0

InteliMains-NT-BTB-3.0-Reference Guide.pdf,

©ComAp – June 2013

164

Range [units]

%LdResStrt 4

.. 110 [%]

Related FW

3.0

Description

This setpoint is used to adjust the load reserve for stop in relative mode. i.e.

Pwr mgmt mode

= REL (%) if the reserve set #4 is active. Learn more about

reserves in the chapter

Reserves, minimal running power

The currently active reserve set is selected by binary inputs

and

. If none of these inputs is active the set #1 is selected.

OTE

The reserve for stop must be always adjusted higher than the reserve for
start.

OTE

# sign in the name of this setpoint marks that this setpoint is shared among
all controllers connected by CAN2 bus.

12.2.8.22

Setpoint: #NextStrt Del

Group

Pwr Management

Range [units]

0 .. 3600 [s]

Related FW

3.0

Description

This setpoint is used to adjust the delay of starting the next gen-set when the
actual

load reserve

drops below the adjusted reserve for start, but the group

is still not overloaded.

OTE

# sign in the name of this setpoint marks that this setpoint is shared among
all controllers connected by CAN2 bus.

12.2.8.23

Setpoint: #OverldNext Del

Group

Pwr Management

Range [units]

0 .. 3600 [s]

Related FW

3.0

Description

If the system reserve drops below the start limit for next gen-set the delay

#NextStrt del

will begin to count down. But if the load raises too quickly it

might happen that the system gets overloaded already before the delay

#NextStrt del

reaches zero.

Содержание IM-NT









































































































































































































































































































































Результаты поиска

Содержание IM-NT

Отзывы:

Похожие инструкции для IM-NT

Бренды по названию

Популярные бренды

ComAp IM-NT, Справочное руководство

Результаты поиска

Содержание IM-NT

Отзывы:

Похожие инструкции для IM-NT

Бренды по названию

Популярные бренды