Cisco SCE 1000 2xGBE Скачать руководство пользователя страница 57

Страница: 57 / 133

Chapter 4 Installation and Maintenance

Removing and Replacing a Power Supply Unit

Cisco SCE 1000 2xGBE Installation and Configuration Guide

OL-7821-05

4-17

Replacing the Power Supply Unit

Warning

Do not mix AC-input and DC-input power supply units in the same

SCE 1000

platform.

To install a new power supply into a

SCE 1000

platform, complete the following steps:

Step 1

Grasp the power supply unit handle with one hand and place your other hand underneath the
power supply for support.

Step 2

Fit the groove in the side of the new power supply module into the guide in the chassis.

Step 3

Gently, but firmly, slide the module into the chassis until its faceplate is flush with the chassis rear
panel.

Warning

When inserting a power supply into the

SCE 1000

platform, do not use unnecessary force; slamming

the power supply into the chassis can damage the connectors on the rear of the power supply.

Step 4

Seat the power supply in the

SCE 1000

platform by tightening the captive installation screw with

a 1/4-inch flat-blade screwdriver.

Note

The power supply is not fully seated until you tighten the installation screw on the faceplate.

This completes the procedures for replacing a power supply in a

SCE 1000

platform.

Reconnecting the Power

The following sections describe how to reconnect the AC or DC power:

•

Reconnecting AC-Input Power Supply Unit

(on page

4-18

)

•

Reconnecting DC-Input Power Supply Unit

(on page

4-18

)

Содержание SCE 1000 2xGBE






































































































































Результаты поиска

Содержание SCE 1000 2xGBE

Отзывы:

Похожие инструкции для SCE 1000 2xGBE

Бренды по названию

Популярные бренды

Cisco SCE 1000 2xGBE, Руководство по установке и настройке

Результаты поиска

Содержание SCE 1000 2xGBE

Отзывы:

Похожие инструкции для SCE 1000 2xGBE

Бренды по названию

Популярные бренды