Cisco SCE 1000 2xGBE Скачать руководство пользователя страница 112 | Manualshive

Страница: 112 / 133

background image

Chapter 8 Troubleshooting

Troubleshooting Tools

Cisco SCE 1000 2xGBE Installation and Configuration Guide

8-4

OL-7821-05

Following is a sample output from the show interface

command.

ip address: 10.1.6.145
subnet mask: 255.255.0.0
Configured duplex: auto
AutoNegotiation is On, link is Up, actual duplex: half

•

show interface

GigabitEthernet 0/#

counters — Displays the values of counters

of a GBE interface.

Following is a sample output from the show interface

counters

command.

In total octets: 191520
In good unicast packets: 560
In good multicast packets: 0
In good broadcast packets: 0
In packets discarded: 0
In packets with CRC/Alignment error: 0
In undersized packets: 0
In oversized packets: 0
Out total octets: 0
Out unicast packets: 0
Out non unicast packets: 0
Out packets discarded: 0

Refer to

The User Log

(on page

8-4

) for an explanation of commands related to the user log.

The User Log

The user log is an ASCII file that can be viewed in any editor. It contains a record of system
events, including startup, shutdown and errors. You can use the Logger to view the user log to
determine whether or not the system is functioning properly, as well as for technical support
purposes.

The Logging System

Events are logged to one of two log files. After a file reaches maximum capacity, the events
logged in that file are then temporarily archived. New events are then automatically logged to the
alternate log file. When the second log file reaches maximum capacity, the system then reverts to
logging events to the first log file, thus overwriting the temporarily archived information stored in
that file.

Basic operations include:

•

Copying the User Log to an external source

•

Viewing the User Log

•

Clearing the User Log

•

Viewing/clearing the User Log counters

«
...
110
111
112
113
114
...
»

Содержание SCE 1000 2xGBE






































































































































Отзывы:

Нет отзывов

Похожие инструкции для SCE 1000 2xGBE

Wireless Router

Бренд: Watchguard Страницы: 11

Бренд: D-Link Страницы: 32

Бренд: D-Link Страницы: 28

Бренд: D-Link Страницы: 48

Бренд: D-Link Страницы: 83

Бренд: D-Link Страницы: 155

Бренд: Lattice Semiconductor Страницы: 15

Бренд: A10 Страницы: 52

3C13886 - Router OC-3 ATM SML Flexible Interface...

Бренд: 3Com Страницы: 171

OfficeConnect WX2200

Бренд: 3Com Страницы: 204

Бренд: Harmonic Страницы: 56

Бренд: Analog Devices Страницы: 76

Бренд: SMART Страницы: 15

Бренд: IOtech Страницы: 16

FieldPoint cFP-RTD-122

Бренд: National Instruments Страницы: 15

Thin Client US310e

Бренд: NEC Страницы: 6

Oresund EFC102200

Бренд: Bridgeworks Страницы: 84

JetStor NAS 724UX

Бренд: AC&NC Страницы: 117

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды