Cisco SCE 1000 2xGBE Скачать руководство пользователя страница 100 | Manualshive

Страница: 100 / 133

background image

Chapter 7 Basic SCE 1000 Platform Operations

Managing SCE 1000 Configurations

Cisco SCE 1000 2xGBE Installation and Configuration Guide

7-4

OL-7821-05

Total warning messages: 0
Total error messages: 0
Total fatal messages: 0

If there are “Total error messages” or “Total fatal messages”, use the

show logger device

User-File-Log

command to display details about the errors.

Managing SCE 1000 Configurations

The procedures for managing

SCE 1000

configurations are explained in the following sections:

•

Viewing Configuration

(on page

7-4

)

•

Saving the Configuration Settings

(on page

7-5

)

•

Recovering a Previous Configuration

(on page

7-6

)

Viewing Configuration

When you enter configuration commands, it immediately effects the SCE platform operation and
configuration. This configuration, referred to as the

running-config

,

is saved in the SCE

platform volatile memory and is effective while the SCE platform is up. After reboot, the SCE
platform loads the

startup-config

, which includes the non-default configuration as saved by

the user, into the

running-config

.

The SCE platform provides commands for:

•

Viewing the running configuration

•

Viewing the startup configuration

After configuring the SCE platform, you may query for the running configuration using the
command

show running-config

.

This command displays the non-default running

configuration. To view all SCE platform running configuration, whether it is the default or not,
you may use the option

all-data

in the

show running-config

command.

To view the running configuration, use the following command:

At the

SCE 1000

#

prompt, type

show running-config

.

The system shows the running configuration.

SCE 1000

#

show running-config

#This is a general configuration file (running-config).
#Created on 15:50:56 CET MON December 11 2005
#cli-type 1
#version 1

clock timezone CET 1
snmp-server community “public” ro
snmp-server host 10.1.1.253 traps version 1 “public”
interface LineCard 0
connection-mode active
no silent
no shutdown
flow-aging default-timeout UDP 60
interface FastEthernet 0/0

«
...
98
99
100
101
102
...
»

Содержание SCE 1000 2xGBE






































































































































Отзывы:

Нет отзывов

Похожие инструкции для SCE 1000 2xGBE

Бренд: Makita Страницы: 2

Network Card-MS

Бренд: Eaton Страницы: 89

SR8800 IM-FW-II

Бренд: H3C Страницы: 107

Бренд: 3Com Страницы: 12

Бренд: H3C Страницы: 16

H3C S3600 Series

Бренд: H3C Страницы: 10

Бренд: H3C Страницы: 42

Бренд: H3C Страницы: 2

H3C S7500E Series

Бренд: H3C Страницы: 34

Бренд: H3C Страницы: 33

Бренд: H3C Страницы: 14

Бренд: H3C Страницы: 56

H3C S7500E Series

Бренд: H3C Страницы: 112

Бренд: H3C Страницы: 15

SR8800 IM-FW-II

Бренд: H3C Страницы: 5

H3C S7500E Series

Бренд: H3C Страницы: 50

Бренд: H3C Страницы: 37

Бренд: H3C Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды