Cisco SCE 1000 2xGBE Скачать руководство пользователя страница 70

Страница: 70 / 133

Chapter 5 Connecting the Management Interfaces and Performing Initial System Configuration

Initial System Configuration

Cisco SCE 1000 2xGBE Installation and Configuration Guide

5-8

OL-7821-05

Note

The default password for all levels is “

cisco

”.

To change the passwords, complete the following steps:

Step 1

The default User password is displayed.

•

To accept the displayed value, press

Enter

•

To change the value, type the desired string and press

Enter

Step 2

The default Admin password is displayed.

•

To accept the displayed value, press

Enter

•

To change the value, type the desired string and press

Enter

Step 3

The default Root password is displayed.

•

To accept the displayed value, press

Enter

•

To change the value, type the desired string and press

Enter

Step 4

Configure password encryption. By default, password encryption is not enabled.

•

To disable password encryption, press

Enter

•

To enable password encryption, type

and press

Enter

XAMPLE

Following is an example of changing all passwords. Password encryption is not enabled (default).

Enter a User password [cisco]:

userin

Enter an Admin password [cisco]:

mng123

Enter a Root password [cisco]:

cistech

Enable passwords encryption? [no]:

Step 4: Configuring Time Settings

The time settings menu configures all time and date related parameters in the system. The time
settings menu includes the following:

•

Time zone

•

Local time

•

Date

•

SNTP menu

Содержание SCE 1000 2xGBE






































































































































Результаты поиска

Содержание SCE 1000 2xGBE

Отзывы:

Похожие инструкции для SCE 1000 2xGBE

Бренды по названию

Популярные бренды

Cisco SCE 1000 2xGBE, Руководство по установке и настройке

Результаты поиска

Содержание SCE 1000 2xGBE

Отзывы:

Похожие инструкции для SCE 1000 2xGBE

Бренды по названию

Популярные бренды