Cisco SCE 1000 2xGBE Скачать руководство пользователя страница 12

Страница: 12 / 133

Preface

Conventions

Cisco SCE 1000 2xGBE Installation and Configuration Guide

OL-7821-05

Conventions

This document uses the following conventions:

Convention Description

boldface

font

Commands and keywords are in

boldface

italic

font

Arguments for which you supply values are in

italics

[ ]

Elements in square brackets are optional.

{x | y | z}

Alternative keywords are grouped in braces and separated by
vertical bars.

[x | y | z]

Optional alternative keywords are grouped in brackets and separated
by vertical bars.

string

A nonquoted set of characters. Do not use quotation marks around
the string, or the string will include the quotation marks.

screen

font

Terminal sessions and information that the system displays are in

screen

font.

boldface screen

font Information you must enter is in

boldface screen

font.

italic screen

font

Arguments for which you supply values are in

italic screen

font.

< >

Nonprinting characters, such as passwords, are in angle brackets.

[ ]

Default responses to system prompts are in square brackets.

!, #

An exclamation point (!) or a pound sign (#) at the beginning of a
line of code indicates a comment line.

Note

Means

reader take note

. Notes contain helpful suggestions or references to materials not covered in this

manual.

Caution

Means

reader be careful

. In this situation, you might do something that could result in equipment

damage or loss of data.

Warning

Means

reader be warned.

In this situation, you might do something that could result in bodily injury.

Содержание SCE 1000 2xGBE






































































































































Результаты поиска

Содержание SCE 1000 2xGBE

Отзывы:

Похожие инструкции для SCE 1000 2xGBE

Бренды по названию

Популярные бренды

Cisco SCE 1000 2xGBE, Руководство по установке и настройке

Результаты поиска

Содержание SCE 1000 2xGBE

Отзывы:

Похожие инструкции для SCE 1000 2xGBE

Бренды по названию

Популярные бренды