Cisco SCE 1000 2xGBE Скачать руководство пользователя страница 49

Страница: 49 / 133

Chapter 4 Installation and Maintenance

Installing the SCE 1000 Platform

Cisco SCE 1000 2xGBE Installation and Configuration Guide

OL-7821-05

4-9

Mounting the System to the Rack

When the appropriate mounting brackets are securely installed, the

SCE 1000

can be installed

into the rack.

To mount the

SCE 1000

to the rack after the brackets are installed, complete the following steps:

Step 1

Make sure that your path to the rack is unobstructed. If the rack is on wheels, ensure that the
brakes are engaged or that the rack is otherwise stabilized.

Step 2

Position the

SCE 1000

so that the front end is closest to you, and lift it carefully to place it into

the rack. To prevent injury, avoid sudden twists or moves.

Step 3

Slide the

SCE 1000

into the rack, pushing it back until the brackets (installed at the front of the

SCE 1000

) meet the mounting strips or posts on both sides of the rack.

A rack with both front and back posts will have the crossrail supports installed. Slide the

SCE

1000

onto these crossrails and push it all the way back.

Figure

4-8: Sliding the SCE Platform into the Rack

Step 4

While keeping the brackets flush against the posts or mounting strips, align the holes in the
brackets with the holes on the rack or mounting strip.

Figure

4-9: Securing the SCE Platform to the Rack

Содержание SCE 1000 2xGBE






































































































































Результаты поиска

Содержание SCE 1000 2xGBE

Отзывы:

Похожие инструкции для SCE 1000 2xGBE

Бренды по названию

Популярные бренды

Cisco SCE 1000 2xGBE, Руководство по установке и настройке

Результаты поиска

Содержание SCE 1000 2xGBE

Отзывы:

Похожие инструкции для SCE 1000 2xGBE

Бренды по названию

Популярные бренды