Cisco SCE 1000 2xGBE Скачать руководство пользователя страница 91

Страница: 91 / 133

Chapter 6 Cabling the Line Ports and Completing the Installation

Connecting the line ports to the network

Cisco SCE 1000 2xGBE Installation and Configuration Guide

OL-7821-05

6-3

Configuring the GBE Interface Parameters

By default, the

SCE 1000

GBE line interface ports are configured with auto-negotiation disabled.

The procedure for enabling auto-negotiation for the GBE line interface ports is explained in the
following section.

Note

Auto-negotiation must be disabled when the

SCE 1000

is deployed via an external optical splitter

(receive-only topology)

Note

If you change any parameters, you must save the new configuration settings.
Type

copy running-config startup-config

, and press

Enter

Configuring Auto-Negotiation

By default, the

SCE 1000

line interface ports are configured with auto-negotiation enabled.

However, when using an external splitter, the auto-negotiation must be disabled.

Note

In order to prevent errors when in bypass mode, the system must be configured so that the speed and
duplex of both line interfaces is the same.

Note

If you change any parameters, you must save the new configuration settings.
Type copy running-config startup-config, and press

Enter.

To configure GBE auto-negotiation for speed and duplex for the first GBE port (subscriber side)
interface:

Step 1

To enter the Global Configuration Mode, at the

SCE 1000

# prompt, type

configure

, and press

Enter

The

SCE 1000

(config)# prompt appears.

Step 2

To enter the first GBE port interface, type

interface GigabitEthernet 0/1

, and press

Enter

The

SCE 1000

(config if)# prompt appears.

Step 3

Type

auto-negotiate

and press

Enter

The

SCE 1000

(config if)# prompt appears.

Содержание SCE 1000 2xGBE






































































































































Результаты поиска

Содержание SCE 1000 2xGBE

Отзывы:

Похожие инструкции для SCE 1000 2xGBE

Бренды по названию

Популярные бренды

Cisco SCE 1000 2xGBE, Руководство по установке и настройке

Результаты поиска

Содержание SCE 1000 2xGBE

Отзывы:

Похожие инструкции для SCE 1000 2xGBE

Бренды по названию

Популярные бренды