Cisco SCE 1000 2xGBE Скачать руководство пользователя страница 39

Страница: 39 / 133

Chapter 3 Topology

Topology-Related Parameters

Cisco SCE 1000 2xGBE Installation and Configuration Guide

OL-7821-05

3-9

Status of the SCE 1000 After Abnormal Boot

This parameter determines whether the

SCE 1000

returns to normal operational state after a

reboot caused by fatal error or abnormal shutdown. In general, it is desirable that the

SCE 1000

resume operation, and as promptly as possible. However, in a redundant topology, a recovered

SCE 1000

may remain non-operational. In this case the platform that had been the backup and is

currently active will remain active.

The two options for this parameter are:

•

Operational

— The status of the

SCE 1000

after abnormal boot is operational. The platform

automatically resumes functioning in the defined operational link bypass mode.

•

Not Operational

— The status of the

SCE 1000

after abnormal boot is not operational. The

platform remains in the defined failure link bypass mode.

This option is to be used only in a redundant topology where a second, operational platform
exists.

Note

Default value =

Operational

for all non-redundant systems.

Must be explicitly configured for redundant topologies.

Table

3-1

Topology Configuration Summary Table

Description Connection

mode

On-failure link
bypass mode

Admin status after
abnormal boot

Link connection via external
switch with port-mirroring

Receive-only

Bypass

Operational

Bump-in-the-wire

Bump-in-the-wire, monitor
and control, not redundant

Inline

Bypass

Operational

Bump-in-the-wire, monitor
only, not redundant

Inline

Bypass

Operational

Bump-in-the-wire, monitor
and control, redundant

Inline Cutoff

Operational[1]

Bump-in-the-wire, monitor
only, redundant

Inline Cutoff

Operational[1]

* Italicized values represent automatically applied defaults that are applied based on previously
defined parameters. These values can be changed only via specific CLI commands.

[1]: In a redundant topology, it is also possible to configure admin status after abnormal boot to be
Not operational. In this case, though, the

SCE 1000

would have to be manually reloaded in order

to resume full functionality.

Содержание SCE 1000 2xGBE






































































































































Результаты поиска

Содержание SCE 1000 2xGBE

Отзывы:

Похожие инструкции для SCE 1000 2xGBE

Бренды по названию

Популярные бренды

Cisco SCE 1000 2xGBE, Руководство по установке и настройке

Результаты поиска

Содержание SCE 1000 2xGBE

Отзывы:

Похожие инструкции для SCE 1000 2xGBE

Бренды по названию

Популярные бренды