Cisco SCE 1000 2xGBE Скачать руководство пользователя страница 92

Страница: 92 / 133

Chapter 6 Cabling the Line Ports and Completing the Installation

Connecting the line ports to the network

Cisco SCE 1000 2xGBE Installation and Configuration Guide

6-4

OL-7821-05

Step 4

To return to Global Configuration Mode, type

exit

and press

Enter

The

SCE 1000

(config)# prompt appears.

Follow the next procedure to configure auto-negotiation for the second GBE port interface

To configure speed and duplex for the second GBE port (network side) interface:

Step 1

At the

SCE 1000

(config)# prompt, to enter the second GBE port interface, type

interface

GigabitEthernet 0/2

, and press

Enter

The

SCE 1000

(config if)# prompt appears.

Step 2

Type

auto-negotiate

and press

Enter

The

SCE 1000

(config if)# prompt appears.

Step 3

To return to Global Configuration Mode, type

exit

and press

Enter

The

SCE 1000

(config)# prompt appears.

Step 4

To exit Global Configuration Mode, type exit and press

Enter

The

SCE 1000

# prompt appears.

Note

Auto-negotiation must be disabled when the

SCE 1000

is deployed via an external optical splitter (i.e.

receive-only topology).

Configure GigabitEthernet Auto-Negotiation

By default, the

SCE 1000

GBE line interface ports are configured with auto-negotiation disabled.

Note

Auto-negotiation must be disabled when the

SCE 1000

is deployed via an external optical splitter

(receive-only topology)

Note

If you change any parameters, you must save the new configuration settings.
Type

copy running-config startup-config

, and press

Enter

Содержание SCE 1000 2xGBE






































































































































Результаты поиска

Содержание SCE 1000 2xGBE

Отзывы:

Похожие инструкции для SCE 1000 2xGBE

Бренды по названию

Популярные бренды

Cisco SCE 1000 2xGBE, Руководство по установке и настройке

Результаты поиска

Содержание SCE 1000 2xGBE

Отзывы:

Похожие инструкции для SCE 1000 2xGBE

Бренды по названию

Популярные бренды