Cisco Network Storage System NSS3000 Series Скачать руководство пользователя страница 169

Страница: 169 / 184

Troubleshooting

LAN LED

Cisco Small Business NSS3000 Series Network Storage System Administration Guide

LAN LED

The

LAN LED

shows the status of the Ethernet link. These are the LED colors and

their meanings:

•

Solid

Green

: The LAN link is up and running at 1000 link speed, but is

currently idle.

•

Flickering Green

: The LAN link is up and running at 1000 link speed and is

currently active. The LED flickers off with activity.

•

Solid Yellow

: The LAN link is up and running at 10/100 link speed, but is

currently idle.

•

Flickering Yellow

: The LAN link is up and running at 10/100 link speed and

is currently active. The LED flickers off with activity.

•

Off

: No LAN link is detected.

Hard Disk Drive LEDs

The

ACT

and

Error

LEDs shows the status of the installed disk drives.

ACT LED

The

ACT

LED states indicates drive activity. These are the LED colors and their

meanings.

•

Solid Green

: The disk drive is configured but is currently idle.

•

Flickering Green

: The disk drive is configured, active, and not rebuilding.

Flickers off with activity.

•

Blinking Green

: The disk drive is configured and a RAID array is currently

rebuilding to the disk drive.

•

Off

: The disk drive is not configured (not part of a RAID or JBOD array and

not exported).

Содержание Network Storage System NSS3000 Series

























































































































































































Результаты поиска

Содержание Network Storage System NSS3000 Series

Отзывы:

Похожие инструкции для Network Storage System NSS3000 Series

Бренды по названию

Популярные бренды

Cisco Network Storage System NSS3000 Series, Руководство администратора

Результаты поиска

Содержание Network Storage System NSS3000 Series

Отзывы:

Похожие инструкции для Network Storage System NSS3000 Series

Бренды по названию

Популярные бренды