Cisco Network Storage System NSS3000 Series Скачать руководство пользователя страница 170

Страница: 170 / 184

Troubleshooting

Reset Button

Cisco Small Business NSS3000 Series Network Storage System Administration Guide

ERR LED

The

ERR

LED states indicates that the disk drive is in an error condition. These are

the LED colors and their meanings

•

Solid Red

: The disk drive is in a failed state.

•

Blinking Red

: The disk drive is predicated to fail (via S.M.A.R.T.). We

recommend that you replace the disk drive to avoid the loss of data.

•

Off

: The drive is OK.

Off

: There is either no UPS attached to the NSS or the UPS function has been

disabled in the

System Power

page in the configuration interface.

: A UPS is attached to the NSS and the UPS function is enabled in the

System

Power

page in the configuration interface.

Reset Button

Use the

Reset

button to restore the network setting system defaults or to reset the

box. The

Reset

button is located to the left of the display button on the front panel

of the NSS. You might need to use a pen or the end of a straightened paperclip to
press the button.

•

To restore the network setting system defaults

Shut down the NSS, press the

Reset

button, and then power up the NSS.

When you see the

Power

LED blink yellow rapidly, release the

Reset

button.

The network settings are restored to the factory defaults.

•

To reset the NSS

Press and hold the

Reset

button while the system is running until the

Power

LED blinks green. Release the

Reset

button.

Содержание Network Storage System NSS3000 Series

























































































































































































Результаты поиска

Содержание Network Storage System NSS3000 Series

Отзывы:

Похожие инструкции для Network Storage System NSS3000 Series

Бренды по названию

Популярные бренды

Cisco Network Storage System NSS3000 Series, Руководство администратора

Результаты поиска

Содержание Network Storage System NSS3000 Series

Отзывы:

Похожие инструкции для Network Storage System NSS3000 Series

Бренды по названию

Популярные бренды