Cisco Network Storage System NSS3000 Series Скачать руководство пользователя страница 168

Страница: 168 / 184

Troubleshooting

NSS LEDs

Cisco Small Business NSS3000 Series Network Storage System Administration Guide

You can also use the

Power Button

LED to perform a graceful shutdown or hard

shutdown of the NSS:

•

To perform a graceful shutdown

: Press the

Power

button and hold for

about 1 to 2 seconds to trigger a graceful shutdown of the NSS.

•

To perform a hard shutdown

: Press the

Power

button and hold for about

eight seconds. Choose this option only if the NSS is not responding to a
graceful shutdown

System LED

The

System (SYS)

LED indicates that a system error has occurred on the NSS.

These are the LED colors and their meanings:

•

Solid Yellow

: Indicates one of these error conditions. You can view the error

through the NSS configuration interface.

A volume is more than 90% full.

A disk drive has failed or is about to fail.

A fan has stalled.

The system temperature is above the maximum threshold.

The temperature of a disk drive is above the maximum threshold.

A voltage rail is above or below specification.

The NSS is running on UPS due to a mains power failure.

•

Solid Red

: Indicates a critical system failure. The system could not boot due

to a corrupted firmware image.

•

Off

: There are no system-related problems

Содержание Network Storage System NSS3000 Series

























































































































































































Результаты поиска

Содержание Network Storage System NSS3000 Series

Отзывы:

Похожие инструкции для Network Storage System NSS3000 Series

Бренды по названию

Популярные бренды

Cisco Network Storage System NSS3000 Series, Руководство администратора

Результаты поиска

Содержание Network Storage System NSS3000 Series

Отзывы:

Похожие инструкции для Network Storage System NSS3000 Series

Бренды по названию

Популярные бренды