Cisco ME 2400 Скачать руководство пользователя страница 94 | Manualshive

Страница: 94 / 106

Cisco ME 2400 Скачать руководство пользователя страница 94

2-82

Cisco ME 3400E, ME 3400, and ME 2400 Ethernet Access Switch System Message Guide

OL-9641-04

Chapter 2 Messages and Recovery Procedures

SW_VLAN Messages

Error Message

SW_VLAN-4-BAD_STARTUP_VLAN_CONFIG_FILE: Failed to configure VLAN from

startup-config. Fallback to use VLAN configuration file from non-volatile memory.

Explanation

This message means that the VLAN software did not use the VLAN configuration from

the startup-configuration file. It will use the binary VLAN configuration file in NVRAM memory.

Recommended Action

No action is required.

Error Message

SW_VLAN-4-BAD_VLAN_CONFIGURATION_FILE: VLAN configuration file

contained incorrect verification word [hex].

Explanation

This message means that the VLAN configuration file read by the VLAN manager did

not begin with the correct value. The VLAN configuration file is invalid, and it has been rejected.
[hex] is the incorrect verification value.

Recommended Action

Find out more about the error by using the

show tech-support

privileged EXEC

command and by copying the error message exactly as it appears on the console or system log and
entering it in the Output Interpreter tool. Use the Bug Toolkit to look for similar reported problems. For
more information about these online tools and about contacting Cisco, see the

“Error Message

Traceback Reports” section on page 1-3

.

Error Message

SW_VLAN-4-BAD_VLAN_CONFIGURATION_FILE_VERSION: VLAN configuration

file contained unknown file version [dec].

Explanation

This message means that the VLAN configuration file read by the VLAN manager

contained an unrecognized file version number, which might mean an attempt to regress to an older
version of the VLAN manager software. [dec] is the file version number.

Recommended Action

Find out more about the error by using the

show tech-support

privileged EXEC

command and by copying the error message exactly as it appears on the console or system log and
entering it in the Output Interpreter tool. Use the Bug Toolkit to look for similar reported problems. For
more information about these online tools and about contacting Cisco, see the

“Error Message

Traceback Reports” section on page 1-3

.

Error Message

SW_VLAN-4-BAD_VLAN_TIMER_ACTIVE_VALUE: Encountered incorrect VLAN

timer active value [chars].

Explanation

This message means that, because of a software error, a VLAN timer was detected as

active when it should have been inactive or as inactive when it should have been active. [chars] is
the VLAN timer active value.

Recommended Action

Copy the message exactly as it appears on the console or in the system log.

Research and attempt to resolve the error by using the Output Interpreter. Use the Bug Toolkit to
look for similar reported problems. If you still require assistance, open a case with the TAC, or
contact your Cisco technical support representative, and provide the representative with the gathered
information. For more information about these online tools and about contacting Cisco, see the

“Error

Message Traceback Reports” section on page 1-3

.

«
...
92
93
94
95
96
...
»

Содержание ME 2400











































































































Отзывы:

Нет отзывов