Cisco ME 2400 Скачать руководство пользователя страница 24

Страница: 24 / 106

2-12

Cisco ME 3400E, ME 3400, and ME 2400 Ethernet Access Switch System Message Guide

OL-9641-04

Chapter 2 Messages and Recovery Procedures

DOT1X Messages

Error Message

DHCP_SNOOPING-6-PARSE_FAILURE: Parsing failed for [dec] bindings.

Explanation

This message means that the specified number of bindings were ignored when the

switch read the database file because the database read operation failed. [dec] is the number of
bindings.

Recommended Action

No action is required.

Error Message

DHCP_SNOOPING-6-VLAN_NOT_SUPPORTED: Vlan not supported. [dec] bindings

ignored.

Explanation

This message means that the specified number of bindings were ignored when the

switch read the database file because VLAN is no longer configured on the switch. [dec] is the
number of bindings that the switch ignores.

Recommended Action

No action required.

DOT1X Messages

This section contains the IEEE 802.1x messages.

Error Message

DOT1X-4-MEM_UNAVAIL: Memory was not available to perform the

802.1X action.

Explanation

This message means that the system memory is not sufficient to perform the 802.1x

authentication.

Recommended Action

Reduce other system activity to reduce memory demands.

Error Message

DOT1X-4-MSG_ERR: Unknown message event received.

Explanation

This message means that the 802.1x process received an unknown message event.

Recommended Action

Restart the 802.1x process by entering the

dot1x system-auth-control

global

configuration command. If this message recurs, reload the device.

Error Message

DOT1X-4-PROC_START_ERR: Dot1x unable to start.

Explanation

This message means that the system failed to create the 802.1x process.

Recommended Action

Restart the 802.1x process by entering the

dot1x system-auth-control

global

configuration command. If this message recurs, reload the device.

Error Message

DOT1X-4-UNKN_ERR: An unknown operational error occurred.

Explanation

This message means that the 802.1x process cannot operate because of an internal

system error.

Recommended Action

No action is required.

Содержание ME 2400











































































































Результаты поиска

Содержание ME 2400

Отзывы:

Cisco ME 2400, Руководство системного сообщения, Страница: 24 / 106

Результаты поиска

Содержание ME 2400

Отзывы: