Cisco ME 2400 Скачать руководство пользователя страница 31

Страница: 31 / 106

2-19

Cisco ME 3400E, ME 3400, and ME 2400 Ethernet Access Switch System Message Guide

OL-9641-04

Chapter 2 Messages and Recovery Procedures

DOT1X_SWITCH Messages

Error Message

DOT1X_SWITCH-5-ERR_VLAN_INVALID: Attempt to assign invalid VLAN [dec]

to 802.1x port [chars]

Explanation

An attempt was made to assign an invalid VLAN to an IEEE 802.1x port. The VLAN

specified is out of range and cannot be assigned to this port.[dec] is the VLAN, and [chars] is the
port.

Recommended Action

Update the configuration to use a valid VLAN.

Error Message

DOT1X_SWITCH-5-ERR_VLAN_NOT_FOUND: Attempt to assign non-existent or

shutdown VLAN [dec] to 802.1x port [chars]

Explanation

An attempt was made to assign a VLAN to an IEEE 802.1x port, but the VLAN was not

found in the VTP database. [dec] is the VLAN, and [chars] is the port.

Recommended Action

Make sure that the VLAN exists and is not shut down, or use another VLAN.

Error Message

DOT1X_SWITCH-5-ERR_VLAN_PROMISC_PORT: Attempt to assign VLAN [dec] to

promiscuous 802.1x port [chars]

Explanation

An attempt was made to assign a VLAN to a promiscuous IEEE 802.1x port, which is

not allowed. [dec] is the VLAN, and [chars] is the port.

Recommended Action

Change the mode of the port so that it is no longer a promiscuous port, or

change the configuration so that no VLAN is assigned.

Error Message

DOT1X_SWITCH-5-ERR_VLAN_RESERVED: Attempt to assign reserved VLAN

[dec] to 802.1x port [chars]

Explanation

An attempt was made to assign an invalid VLAN to an IEEE 802.1x port. The VLAN

specified is a reserved VLAN and cannot be assigned to this port. [dec] is the VLAN, and [chars] is
the port.

Recommended Action

Update the configuration to not use this VLAN.

Error Message

DOT1X_SWITCH-5-ERR_VLAN_ROUTED_PORT: Attempt to assign VLAN [dec] to

routed 802.1x port [chars]

Explanation

An attempt was made to assign a VLAN to a routed IEEE 802.1x port, which is not

allowed. [dec] is the VLAN, and [chars] is the port.

Recommended Action

Change the mode of the port so that it is no longer a routed port, or change the

configuration so that no VLAN is assigned.

Содержание ME 2400











































































































Результаты поиска

Содержание ME 2400

Отзывы:

Cisco ME 2400, Руководство системного сообщения, Страница: 31 / 106

Результаты поиска

Содержание ME 2400

Отзывы: