Cisco ME 2400 Скачать руководство пользователя страница 28

Страница: 28 / 106

2-16

Cisco ME 3400E, ME 3400, and ME 2400 Ethernet Access Switch System Message Guide

OL-9641-04

Chapter 2 Messages and Recovery Procedures

DOT1X Messages

Error Message

DOT1X-5-ERR_VLAN_RSPAN_CONFIGURED: VLAN [dec] is configured as a

Remote SPAN VLAN, which has Dot1x enabled interface(s) configured. Please disable

Dot1x on all ports in this VLAN or do not enable RSPAN on this VLAN.

Explanation

This message means that remote SPAN should not be enabled on a VLAN in which ports

are configured with 802.1x enabled. [dec] is the VLAN ID.

Recommended Action

Either disable the remote SPAN configuration on the VLAN, or disable 802.1x

on all the ports in this VLAN.

Error Message

DOT1X-5-INVALID_INPUT: Dot1x Interface parameter is Invalid on

interface [chars].

Explanation

The IEEE 802.1x interface parameter is out of the specified range or is invalid. [chars]

is the interface.

Recommended Action

Refer to the CLI help documentation to determine the valid IEEE 802.1x

parameters.

Error Message

DOT1X-5-INVALID_MAC: Invalid MAC address (zero, broadcast or multicast

mac address [chars] is trying to authenticate).

Explanation

This message means that authentication was attempted for a zero, broadcast, or

multicast MAC address using 802.1x. 802.1x authentication is allowed only for a valid nonzero,
nonbroadcast, or nonmulticast source MAC address.

Recommended Action

Connect a 802.1x-supported host to the 802.1x-enabled port.

Error Message

DDOT1X-5-NOT_DOT1X_CAPABLE: Dot1x disabled on interface [chars]

because it is not an Ethernet interface.

Explanation

This message means that you can enable 802.1x authentication only on Ethernet

interfaces. [chars] is the interface.

Recommended Action

Enable 802.1x authentication only on Ethernet interfaces.

Error Message

DOT1X-5-SECURITY_VIOLATION: Security violation on the interface

[chars], new MAC address [enet] is seen.

Explanation

A host on the specified interface is trying to access the network or to authenticate in a

host mode that does not support the number of hosts attached to the interface. This is a security
violation, and the port is put in the error-disabled state.

Recommended Action

Ensure that the interface is configured to support the number of attached hosts.

Enter the

shutdown

interface configuration command and then the

no shutdown

interface

configuration command to restart the port.

Содержание ME 2400











































































































Результаты поиска

Содержание ME 2400

Отзывы:

Cisco ME 2400, Руководство системного сообщения, Страница: 28 / 106

Результаты поиска

Содержание ME 2400

Отзывы: