manualshive.com logo in svg

Cisco ME 2400, Руководство системного сообщения, Страница: 26 / 106

Поделиться
Скачать
Cisco ME 2400 Скачать руководство пользователя страница 26

 

2-14

Cisco ME 3400E, ME 3400, and ME 2400 Ethernet Access Switch System Message Guide

OL-9641-04

Chapter 2      Messages and Recovery Procedures

DOT1X Messages

Error Message   

DOT1X-5-ERR_PROTO_TUNNELLING: Dot1x can not be enabled on protocol 

tunnelling enabled ports.

Explanation   

This message means that 802.1x could not be enabled on the protocol-tunneling-enabled 

port. Trying to set 802.1x port-control to 

auto

 or 

force-unauthorized

 (force_unauth) mode on a 

protocol-tunneling-enabled port, which is not allowed, caused this condition.

Recommended Action   

Change the access VLAN on the interface, and then enable 802.1x.

Error Message   

DOT1X-5-ERR_PVLAN_TRUNK:Dot1x can not be enabled on private VLAN trunk 

ports

Explanation   

This message means that 802.1x could not be enabled on private VLAN ports on which 

trunking is enabled.

Recommended Action   

No action is required.

Error Message   

DOT1X-5-ERR_RSPAN_VLAN: Dot1x can not be enabled on ports configured 

in Remote SPAN vlan.

Explanation   

This message means that 802.1x could not be enabled on the remote SPAN VLAN port. 

Trying to set 802.1x port-control to 

auto

 or 

force-unauthorized

 (force_unauth) mode on a port that 

is in a remote SPAN VLAN, which is not allowed, caused this condition.

Recommended Action   

Disable remote SPAN on the VLAN, and then enable 802.1x.

Error Message   

DOT1X-5-ERR_SPANDST: Dot1x can not be enabled on [chars]. It is 

configured as a SPAN Dest port. 

Explanation   

This message means that 802.1x cannot be enabled on a port that is a SPAN destination 

port because these features are mutually exclusive. [chars] is the port.

Recommended Action   

Remove the SPAN destination port from the SPAN session before 

reconfiguring 802.1x on the port.

Error Message   

DOT1X-5-ERR_TRUNK: Dot1x can not be enabled on Trunk port.

Explanation   

This message means that 802.1x could not be enabled on the trunk port. Trying to set 

802.1x port control to 

auto

 or 

force-unauthorized

 (force_unauth) mode on a trunk port, which is not 

allowed, caused this condition.

Recommended Action   

Disable trunking on the interface, and then enable 802.1x.

Содержание ME 2400











































































































Отзывы:

Нет отзывов