manualshive.com logo in svg

Cisco ME 2400, Руководство системного сообщения, Страница: 101 / 106

Поделиться
Скачать
Cisco ME 2400 Скачать руководство пользователя страница 101

 

2-89

Cisco ME 3400E, ME 3400, and ME 2400 Ethernet Access Switch System Message Guide

OL-9641-04

Chapter 2      Messages and Recovery Procedures

VQPCLIENT Messages

VQPCLIENT Messages

This section contains VLAN Query Protocol (VQP) client messages. 

Error Message   

VQPCLIENT-2-CHUNKFAIL: Could not allocate memory for VQP. 

Explanation   

This message means that an error occurred when the system tried to allocate memory 

for the VQP client. 

Recommended Action   

Copy the message exactly as it appears on the console or in the system log. 

Research and attempt to resolve the error by using the Output Interpreter. Use the Bug Toolkit to 
look for similar reported problems. If you still require assistance, open a case with the TAC, or 
contact your Cisco technical support representative, and provide the representative with the gathered 
information. For more information about these online tools and about contacting Cisco, see the 

“Error 

Message Traceback Reports” section on page 1-3

.

Error Message   

VQPCLIENT-2-DENY: Host [enet] denied on interface [chars]. 

Explanation   

This message means that the VLAN Membership Policy Server (VMPS) has denied 

access for the given host MAC address to an interface. [enet] is the host MAC address, and [chars] 
is the interface name.

Recommended Action   

No action is normally required. If you think that the host should have been 

allowed access, verify the configuration on the VMPS. 

Error Message   

VQPCLIENT-2-TOOMANY: Interface [chars] shutdown by active host limit. 

Explanation   

This message means that the system has shut down an interface because too many hosts 

have requested access to that port. [chars] is the interface name.

Recommended Action   

To reactivate the port, remove the excess hosts, and enter a 

no shutdown

 

interface configuration command on the interface. 

Error Message   

VQPCLIENT-3-IFNAME: Invalid interface ([chars]) in response. 

Explanation   

This message means that the VMPS has sent an unsolicited response with an unknown 

interface name. [chars] is the name of the unknown interface.

Recommended Action   

Verify the VMPS configuration. 

Error Message   

VQPCLIENT-3-VLANNAME: Invalid VLAN ([chars]) in response. 

Explanation   

This message means that the VMPS has specified a VLAN name that is unknown to the 

switch. [chars] is the invalid VLAN name.

Recommended Action   

Make sure that the VLAN exists on the switch. Verify the VMPS configuration. 

Содержание ME 2400











































































































Отзывы:

Нет отзывов