Cisco ME 2400 Скачать руководство пользователя страница 78

Страница: 78 / 106

2-66

Cisco ME 3400E, ME 3400, and ME 2400 Ethernet Access Switch System Message Guide

OL-9641-04

Chapter 2 Messages and Recovery Procedures

REP Messages

This section contains the Resilient Ethernet Protocol (REP) messages.

Note

These messages apply only to the Cisco ME 3400E and ME 3400 switches.

Error Message

REP-4-LINKSTATUS: [chars] (segment [dec]) is [chars]

Explanation

The Resilient Ethernet Protocol (REP) link status has changed. The first [chars] is the

interface name that has a link-status change. The [dec] is the REP segment number of the interface.
The second [chars] is the new link status.

Recommended Action

No action is required.

Error Message

REP-5-PREEMPTIONFAIL: can not perform preemption on segment [dec] due

to [char]

Explanation

The Resilient Ethernet Protocol (REP) preempt operation failed. This could be due to

an invalid port ID or a neighbor_offset number specified with the

rep block port

interface

configuration command. This could also be caused by entering the

rep block port preferred

interface configuration command if there is no REP port configured with the

preferred

keyword.

[dec] is the segment number, and [char] is the reason for the failure.

Recommended Action

Correct the configuration, and run REP manual pre-emption on the primary

edge port by entering the

rep preempt segment

command.

RMON Messages

This section contains the Rmote Network Monitoring (RMON) messages.

Error Message

RMON-5-FALLINGTRAP: Falling trap is generated because the value of

[chars] has fallen below the falling-threshold value [dec].

Explanation

This message means that a falling trap has been generated. The value of the specified

MIB object has fallen below the falling threshold value. [chars] is the MIB object, and [dec] is the
threshold value.

Recommended Action

Take appropriate action on the specified MIB object.

Error Message

RMON-5-RISINGTRAP: Rising trap is generated because the value of

[chars] exceeded the rising-threshold value [dec].

Explanation

This message means that a rising trap has been generated. The value of the specified

MIB object has exceeded the rising threshold value. [chars] is the MIB object, and [dec] is the
threshold value.

Recommended Action

Take appropriate action on the specified object.

Содержание ME 2400











































































































Результаты поиска

Содержание ME 2400

Отзывы:

Cisco ME 2400, Руководство системного сообщения, Страница: 78 / 106

Результаты поиска

Содержание ME 2400

Отзывы: