Cisco DPA 7610 Скачать руководство пользователя страница 128

Страница: 128 / 188

Chapter 7

Troubleshooting the DPA 7630/7610

Interpreting LED Status

7-6

Cisco DPA 7630/7610 Voice Mail Gateways Administration Guide

78-11069-03

Interpreting LED Status

The DPA 7630/7610 includes several LED status indicators on the front panel
(see

Figure 7-1

Table 7-2

includes descriptions of these LEDs.

Voice mail hunt groups
containing more than 13
extensions can cause voice
mail access to fail with an
error tone.

By default, the Cisco CallManager
supports a maximum of 12
forwarding hops, leading to a
maximum of 13 extensions in any
one hunt group.

To avoid this error, do one of the
following:

•

Set the hop count system
parameter to more than 12.

•

Divide the DPA 7630/7610 into
several hunt groups (possibly all
in the same forwarding chain) to
improve load balance.

Refer to the

“Setting Up the

Voice Mail Hunt Group” section
on page 4-5

Table 7-1

DPA 7630/7610 Troubleshooting Suggestions (continued)

Symptom

Solution

For More Information

Table 7-2

LED Status Explanation

LED

Flashing

Off

Power

Power connected and
operating normally

N/A

Power not connected

Status

Operating normally

Potential hardware error
detected.

Check the event log for
details.

Not operating normally

N/A

Packet transmitted.

Nothing transmitted

N/A

Packet received.

Nothing received

100 MBPS

Connected at 100 Mbps

N/A

Connected at 10 Mbps or
not connected

Содержание DPA 7610





























































































































































































Результаты поиска

Содержание DPA 7610

Отзывы:

Похожие инструкции для DPA 7610

Бренды по названию

Популярные бренды

Cisco DPA 7610, Руководство администратора

Результаты поиска

Содержание DPA 7610

Отзывы:

Похожие инструкции для DPA 7610

Бренды по названию

Популярные бренды