2-100
Cisco ONS 15600 SDH Troubleshooting Guide, R8.0
July 2010
Chapter 2 Alarm Troubleshooting
2.6.153 MSSP-SW-VER-MISM
An RFI occurs when the ONS 15600 SDH detects an RFI in the SDH overhead because of a fault in
another node. Resolving the fault in the adjoining node clears the MS-RFI condition in the reporting
node.
Clear the MS-RFI Condition
Step 1
Log into the far-end node of the reporting ONS 15600 SDH.
Step 2
Determine whether there are other alarms, especially the
“LOS (STMN)” alarm on page 2-86
.
Step 3
Clear the main alarm. See the appropriate alarm section in this chapter for the procedure.
Step 4
If the condition does not clear, log into the Cisco Technical Support Website at
http://www.cisco.com/techsupport for more information or log into
http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml to obtain a directory of toll-free
Technical Support numbers for your country.
2.6.153 MSSP-SW-VER-MISM
Default Severity: Major (MJ), Service-Affecting (SA)
SDH Logical Object: STMN
The MS-SPRing Software Version Mismatch alarm is by the TSC card when it checks all software
versions for all nodes in a ring and discovers a mismatch in versions.
Clear the MSSP-SW-VER-MISM Alarm
Step 1
Clear the alarm by loading the correct software version on the TSC card with the incorrect load. To
download software, refer to the release-specific software download document.
Step 2
If the condition does not clear, log into the Cisco Technical Support Website at
http://www.cisco.com/techsupport for more information or log into
http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml to obtain a directory of toll-free
Technical Support numbers for your country to report a Service-Affecting (SA) problem.
2.6.154 MS-SQUELCH-HP
Default Severity: Not Alarmed (NA), Non-Service-Affecting (NSA)
SDH Logical Object: STMN
The Multiplex Section Ring is Squelching High-Order Path Traffic condition is raised on an STM-N
facility. If the node failure scenario includes the source node, the node that drops the signal will squelch
traffic. The condition resolves when the node recovers.
This condition is raised with an NA severity by default. However, it indicates that traffic is squelched
due to node failure (traffic outage). Traffic outages can be caused by different problems, such as multiple
LOS alarms, MS-AIS, or node power outages. MS-SQUELCH-HP is symptomatic and indicates that the
user must investigate which node in a ring is being isolated and what is causing the node isolation.
Содержание Cisco ONS 15600 SDH
