manualshive.com logo in svg

Cisco Cisco ONS 15600 SDH, Руководство по устранению неисправностей

Продукт Cisco ONS 15600 SDH - это мощное устройство для оптоволоконной связи. У вас возникли проблемы с оборудованием? Скачайте бесплатно Руководство по устранению неисправностей на manualshive.com. Наша подробная инструкция поможет вам быстро и эффективно решить любую проблему.

Поделиться
Скачать
background image

2-11

Cisco ONS 15600 SDH Troubleshooting Guide, R8.0

July 2010

Chapter 2 Alarm Troubleshooting

2.5   Trouble Notifications

2.5  Trouble Notifications

The ONS 15600 SDH system reports trouble by utilizing standard alarm and condition characteristics, 
standard severities following the rules in Telcordia GR-253-CORE, and graphical user interface (GUI) 
state indicators. These notifications are described in the following paragraphs.

The ONS 15600 SDH uses standard Telcordia categories to characterize levels of trouble. The system 
reports trouble notifications as alarms and status or descriptive notifications (if configured to do so) as 
conditions in the CTC Alarms window. Alarms typically signify a problem that the user needs to remedy, 
such as a loss of signal. Conditions do not necessarily require troubleshooting.

2.5.1  Alarm Characteristics

The ONS 15600 SDH uses standard alarm entities to identify what is causing trouble. All alarms stem 
from hardware, software, environment, or operator-originated problems whether or not they affect 
service. Current alarms for the network, CTC session, node, or card are listed in the Alarms tab. (In 
addition, cleared alarms are also found in the History tab.)

2.5.2  Condition Characteristics

Conditions include any problem detected on an ONS 15600 SDH shelf. They might include standing or 
transient notifications. A snapshot of all current raised, standing conditions on the network, node, or card 
can be retrieved in the CTC Conditions window or using TL1's set of RTRV-COND commands. (In 
addition, some but not all cleared conditions are also found in the History tab.)

For a comprehensive list of all conditions, refer to the 

Cisco ONS SDH TL1 Command Guide

. For a 

comprehensive list of all transient conditions, see 

Chapter 3, “Transient Conditions.”

2.5.3  Severities

The ONS 15600 SDH uses Telcordia-devised standard severities for alarms and conditions:

  •

A Critical (CR) alarm generally indicates severe, Service-Affecting (SA) trouble that needs 
immediate correction. 

  •

A Major (MJ) alarm is a serious alarm, but the trouble has less impact on the network.

  •

Minor (MN) alarms generally are those that do not affect service. For example, the automatic 
protection switching (APS) byte failure (APSB) alarm indicates that line terminating equipment 
(LTE) detects a byte failure on the signal that could prevent traffic from properly executing a traffic 
switch.

  •

Not Alarmed (NA) conditions are information indicators, such as for the free-running 
synchronization (FRNGSYNC) state. They might or might not require troubleshooting, as indicated 
in the entries.

  •

Not Reported (NR) conditions occur as a secondary result of another event. For example, the alarm 
indication signal (AIS), with severity NR, is inserted by a downstream node when an LOS (CR or 
MJ) alarm occurs upstream. These conditions do not in themselves require troubleshooting, but are 
to be expected in the presence of primary alarms.

Содержание Cisco ONS 15600 SDH































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Cisco ONS 15600 SDH

dbx ProVocal Specifications preview
ProVocal
Бренд: dbx Страницы: 2
H3C SR6600 Series Faq preview
SR6600 Series
Бренд: H3C Страницы: 22
H3C S5800-60C-PWR Ordering Manual preview
S5800-60C-PWR
Бренд: H3C Страницы: 3
H3C S5120V3-EI Series Manual preview
S5120V3-EI Series
Бренд: H3C Страницы: 54
Ublox LENA-R8 Series System Integration Manual preview
LENA-R8 Series
Бренд: Ublox Страницы: 116
H3C CR16000-M Installation Manual preview
CR16000-M
Бренд: H3C Страницы: 116
Paradyne COMSPHERE 3610 User Manual preview
COMSPHERE 3610
Бренд: Paradyne Страницы: 112
Cambium Networks PMP 450 Series User Manual preview
PMP 450 Series
Бренд: Cambium Networks Страницы: 215
Lanner NCA-4035 User Manual preview
NCA-4035
Бренд: Lanner Страницы: 109
Aztech DSL1000EW(L) Speci?Cations preview
DSL1000EW(L)
Бренд: Aztech Страницы: 2
8e6 Technologies ER3-100 (5K02-55) Quick Start Manual preview
ER3-100 (5K02-55)
Бренд: 8e6 Technologies Страницы: 74
Abocom WM3111 Specification preview
WM3111
Бренд: Abocom Страницы: 1
Garderos R-7700 Series Operating Manual preview
R-7700 Series
Бренд: Garderos Страницы: 23
U.S. Products maxg Quick Installation Manual preview
maxg
Бренд: U.S. Products Страницы: 80
SAGEMCOM SE681 WiMAX User Manual preview
SE681 WiMAX
Бренд: SAGEMCOM Страницы: 75
Adaptec AAA-130SA SERIES Installation And Hardware Manual preview
AAA-130SA SERIES
Бренд: Adaptec Страницы: 94
QTech QSW-2900 User Manual preview
QSW-2900
Бренд: QTech Страницы: 406
Boss Vocal Performer VE-20 Owner'S Manual preview
Vocal Performer VE-20
Бренд: Boss Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды