manualshive.com logo in svg

Cisco Catalyst 3550, Руководство по настройке программного обеспечения

Функциональный коммутатор Cisco Catalyst 3550 предлагает широкий спектр возможностей для настройки сети. Пользователи могут легко настроить устройство, используя Бесплатное руководство по программному обеспечению, которое можно скачать с manualshive.com. Удобный интерфейс и высокое качество работы делают Catalyst 3550 отличным выбором для вашей сети.

Поделиться
Скачать
background image

 

8-22

Catalyst 3550 Multilayer Switch Software Configuration Guide

78-11194-03

Chapter 8      Configuring Interface Characteristics

Configuring Layer 3 Interfaces

To verify that an interface is disabled, enter the show interfaces privileged EXEC command. A disabled 
interface is shown as administratively down in the show interface command display as with Gigabit 
Ethernet interface 0/1 in this example.

Switch# show interfaces 

<output truncated>

GigabitEthernet0/2 is administratively down, line protocol is down

  Hardware is Gigabit Ethernet, address is 0002.4b29.4403 (bia 0002.4b29.4403)

  MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,

     reliability 255/255, txload 1/255, rxload 1/255

  Encapsulation ARPA, loopback not set

  Keepalive set (10 sec)

  Auto-duplex, Auto-speed

<output truncated>

Configuring Layer 3 Interfaces

The Catalyst 3550 with the enhanced multilayer software image supports three types of Layer 3 
interfaces for routing and bridging:

•

SVIs: You should configure SVIs for any VLANs for which you want to route traffic. SVIs are 
created when you enter a VLAN ID following the interface vlan global configuration command. To 
delete an SVI, use the no interface vlan global configuration command.

For information about assigning Layer 2 ports to VLANs, see 

Chapter 9, “Creating and Maintaining 

VLANs.”

•

Layer 3 EtherChannel ports: EtherChannel interfaces made up of routed ports.

EtherChannel port interfaces are described in 

Chapter 21, “Configuring EtherChannel.”

•

Routed ports: Routed ports are physical ports configured to be in Layer 3 mode by using the no 
switchport interface configuration command.

Note

A Layer 3 switch can have an IP address assigned to each routed port and SVI. The number of routed 
ports and SVIs that you can configure is not limited by software; however, the interrelationship 
between this number and the number of other features being configured might have an impact on 
CPU utilization because of hardware limitations. For more information about feature combinations, 
see the 

“Optimizing System Resources for User-Selected Features” section on page 6-57

.

All Layer 3 interfaces require an IP address to route traffic. The following procedure shows how to 
configure an interface as a Layer 3 interface and how to assign an IP addresses to an interface.

Note

If the physical port is in Layer 2 mode (the default), you must enter the no switchport interface 
configuration command to put the interface into Layer 3 mode. Entering a no switchport command 
disables and then re-enables the interface, which might generate messages on the device to which the 
interface is connected. When you use this command to put the interface into Layer 3 mode, you are 
also deleting any Layer 2 characteristics configured on the interface.

Содержание Catalyst 3550































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 3550

DAVIS WeatherLink Addendum preview
WeatherLink
Бренд: DAVIS Страницы: 20
Partec ParaStation5 Administrator'S Manual preview
ParaStation5
Бренд: Partec Страницы: 98
Intergraph InterSite Quick Start Manual preview
InterSite
Бренд: Intergraph Страницы: 46
Red Hat JBoss Developer Studio 3.0 User Reference Manual preview
JBoss Developer Studio 3.0
Бренд: Red Hat Страницы: 78
Bosch VIDOS Installation And Operating Manual preview
VIDOS
Бренд: Bosch Страницы: 40
Bosch Divar Archive Player Operation Manual preview
Divar Archive Player
Бренд: Bosch Страницы: 10
Bosch MBV-BPRO-40 Operator'S Manual preview
MBV-BPRO-40
Бренд: Bosch Страницы: 86
Bosch DINION IP 5000 MP Software Manual preview
DINION IP 5000 MP
Бренд: Bosch Страницы: 112
Seagate BlackArmor WS 110 Quick Start Manual preview
BlackArmor WS 110
Бренд: Seagate Страницы: 2
Internet Security Systems RealSecure User Manual preview
RealSecure
Бренд: Internet Security Systems Страницы: 126
MACROMEDIA Director MX Use Manual preview
Director MX
Бренд: MACROMEDIA Страницы: 624
Garmin Pilot for Android User Manual preview
Pilot for Android
Бренд: Garmin Страницы: 150
Avaya PARTNER ACS PC Administration Getting Started Manual preview
PARTNER ACS PC Administration
Бренд: Avaya Страницы: 56
Avaya P120 SMON User Manual preview
P120 SMON
Бренд: Avaya Страницы: 61
Red Hat APPLICATION STACK 1.1 RELEASE Release Note preview
APPLICATION STACK 1.1 RELEASE
Бренд: Red Hat Страницы: 30
Denon DP-200USB Service Manual preview
DP-200USB
Бренд: Denon Страницы: 38
Bay Networks FastLink II User Manual preview
FastLink II
Бренд: Bay Networks Страницы: 112
Macrovision Corporation SAMREPORT-LITE 2006 Manual preview
SAMREPORT-LITE 2006
Бренд: Macrovision Corporation Страницы: 36

Бренды по названию

Популярные бренды

Загрузить еще бренды