Cisco 7246 - uBR Router Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 238

background image

2-10

Cisco uBR7200 Series Universal Broadband Router Hardware Installation Guide

OL-5421-03

Chapter 2 Preparing the Cisco uBR7200 Series Router for Installation

Shipping Container Contents

Note

For headend RF and data setups, refer to

Chapter 4, “Connecting the Cisco uBR7200 Series Router to

the Cable Headend.”

Refer to

Appendix F, “Manufacturers for Headend Provisioning Requirements,”

for

a list of manufacturers. Refer to

Appendix C, “Cable Specifications,”

for coaxial cabling specifications.

In addition, you might need the following:

•

Crossover Ethernet cable with RJ-45 connectors—If you plan to connect a computer directly to an
Ethernet port on a PA-4E port adapter or a PA-8E port adapter installed in the Cisco uBR7200 series
router, you need this type of cable.

•

Data service unit (DSU) to connect each serial port to an external network.

•

One serial port adapter cable for each serial port to connect the port with the remote device or
network. (The operating speeds of the port interfaces, and other information specific to each port
adapter, can be found in the respective port adapter configuration notes.)

•

To connect a serial port to a T1 network, you need a T1 CSU/DSU that converts the High-Level Data
Link Control (HDLC) synchronous serial data stream into a T1 data stream with the correct framing
and ones density. (Some telephone systems require a minimum number of 1 bit per time unit in a
data stream, called

ones density

.) Several T1 CSU/DSU devices are available as additional

equipment, and most provide either a V.35, EIA/TIA-449, or EIA-530 electrical interface.

•

Fast Ethernet transceiver.

•

Cisco uBR900 series cable access router or DOCSIS-based STB and CPE devices to test full system
functionality.

Note

The Cisco uBR900 is End of Life for some models.

Note

When the Cisco uBR7200 series router starts running, IF downstream output is generated. For more
information, see the

“Powering On the Cisco uBR7200 Series Router” section on page 3-25

.

Shipping Container Contents

When you receive your Cisco uBR7200 series universal broadband router, use the following procedure
to check the contents of the shipping container. Use the

Cisco uBR7200 Series Router Installation

Checklist

in

Table 3-1

or the

“Cisco uBR7246 and Cisco uBR7246VXR Component List” section on

page 2-21

to ensure you received all the components that you ordered.

Note

Do not discard the shipping container. You will need the container if you move or ship your

Cisco uBR7200 series router in the future.

«
...
54
55
56
57
58
...
»

Содержание 7246 - uBR Router















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7246 - uBR Router

Бренд: BandLuxe Страницы: 67

Бренд: Farallon Страницы: 26

Бренд: Observint Страницы: 11

SISPM1040-582-LRT

Бренд: Lantronix Страницы: 2

Бренд: Lantronix Страницы: 7

Maestro E220 Series

Бренд: Lantronix Страницы: 25

Бренд: National Instruments Страницы: 17

Бренд: National Instruments Страницы: 16

Бренд: National Instruments Страницы: 23

INTERNET PRIVACY PROTECTION

Бренд: AlphaShield Страницы: 49

Sentry Global Security Modem

Бренд: Server Technology Страницы: 22

USB-BRIDGEV2-EVAL

Бренд: IDT Страницы: 11

NetIron MLXe Series

Бренд: Brocade Communications Systems Страницы: 305

UniFi Cloud Key

Бренд: Ubiquiti Страницы: 13

BROADCAST POLLING FRAD BPF-14 BU

Бренд: DCB Страницы: 28

Бренд: ANEP Страницы: 48

Бренд: ZyXEL Communications Страницы: 2

Бренд: Zoom Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды