manualshive.com logo in svg

Cisco 7246 - uBR Router, Руководство по установке оборудования

Cisco 7246 - uBR Router - позволяет эффективно управлять сетями. Подробное описание установки оборудования содержится в Hardware Installation Manual. Бесплатно загружайте руководство с manualshive.com, чтобы узнать, как правильно установить и использовать этот роутер.

Поделиться
Скачать
background image

1-23

Cisco uBR7200 Series Universal Broadband Router Hardware Installation Guide

OL-5421-03

Chapter 1      Cisco uBR7200 Series Overview

  Hardware Component Descriptions

Figure 1-10

Cisco uBR7246 and Cisco uBR7246VXR DC-Input Power Supply

Caution

To ensure adequate airflow across the Cisco uBR7246VXR and Cisco uBR7246 universal broadband 
routers power supplies, a power supply or a power supply filler plate (with its attached air dam) must be 
installed in each power supply bay.

Note

See 

Appendix A, “Cisco uBR7200 Series Router Specifications,”

 for AC-input and DC-input power 

supply system power specifications, including input voltage and operating frequency ranges.

The Power OK LED goes off and the power supply shuts itself down when the internal DC voltages 
exceed allowable tolerances or the internal temperature of the power supply exceeds allowable 
tolerances. The power supply then attempts to restart itself within 10 seconds of the shutdown. If the 
power supply cannot restart itself on the first attempt, it repeats the automatic restart sequence until the 
power switch is manually switched to the off position, or the power cord is disconnected from the back 
of the power supply or the power source. For a description of power supply shutdown conditions and 
thresholds, refer to the 

“Environmental Monitoring and Reporting Functions” section on page 5-2

.

Caution

When the input power to Cisco uBR7200 series universal broadband router power supply is disconnected 
or lost, the power supply enters a reset cycle for 10 seconds. Wait at least 10 seconds or move the power 
switch from one position to the other to restart the power supply. For example, if the power supply was 
on when the power was disconnected or lost, move the power switch to the off position then back to the 
on position. If you do not wait the full 10 seconds or move the power switch from one position to the 
other, the power supply does not restart.

Fan Trays

The fan tray for the Cisco uBR7246VXR and Cisco uBR7246, shown in 

Figure 1-11

, consists of

 

seven 

fans that are attached to a metal tray. 

In each of the Cisco uBR7200 series routers, the fan tray is located on the left side of the chassis (when 
viewing the router from the front) and receives 12 VDC through a DC power harness that connects 
directly to the router midplane. 

12109

Handle

Captive installation screw

Power 

switch

Power 
receptacle

M5 grounding

Strain-relief 

Содержание 7246 - uBR Router















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7246 - uBR Router

Linksys WRT54G3G-AT Product Data preview
WRT54G3G-AT
Бренд: Linksys Страницы: 2
IEI Technology KINO-KBN-i2 Quick Installation Manual preview
KINO-KBN-i2
Бренд: IEI Technology Страницы: 21
Jabra A330 Multiuse User Manual preview
A330 Multiuse
Бренд: Jabra Страницы: 15
Datasat AP25 Installation And Operating Manual preview
AP25
Бренд: Datasat Страницы: 170
Tripp Lite N48M Series Installation Manual preview
N48M Series
Бренд: Tripp Lite Страницы: 20
Ruckus Wireless ZoneFlex 7731 Getting Started Manual preview
ZoneFlex 7731
Бренд: Ruckus Wireless Страницы: 56
Renesas RSKH836079 Quick Start Manual preview
RSKH836079
Бренд: Renesas Страницы: 6
IntesisBox IBOX-BAC Series Installation Sheet preview
IBOX-BAC Series
Бренд: IntesisBox Страницы: 2
Linksys WRT54GR - Wireless-G Broadband Router Quick Installation Manual preview
WRT54GR - Wireless-G Broadband Router
Бренд: Linksys Страницы: 81
Parker ACR1200 Hardware Manual preview
ACR1200
Бренд: Parker Страницы: 50
SurfControl 509-8629-00 Setup Manual preview
509-8629-00
Бренд: SurfControl Страницы: 2
OPTO 22 PCI-AC48 User Manual preview
PCI-AC48
Бренд: OPTO 22 Страницы: 28
Amer.com 8-Port 10/100Mbps Fast Ethernet Switch User Manual preview
8-Port 10/100Mbps Fast Ethernet Switch
Бренд: Amer.com Страницы: 14
Dantel 44118 Installation & Operation Manual preview
44118
Бренд: Dantel Страницы: 22
Asante IntraSwitch 5324MT Quick Installation Manual preview
IntraSwitch 5324MT
Бренд: Asante Страницы: 2
Rane CP 52S Operator'S Manual preview
CP 52S
Бренд: Rane Страницы: 6
LevelOne NVR-0432 User Manual preview
NVR-0432
Бренд: LevelOne Страницы: 142
ORiNG IES-3082GC User Manual preview
IES-3082GC
Бренд: ORiNG Страницы: 101

Бренды по названию

Популярные бренды

Загрузить еще бренды