Cisco 7246 - uBR Router Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 238

background image

x

Cisco uBR7200 Series Universal Broadband Router Hardware Installation Guide

OL-5421-03

Preface

The guide contains procedures to unpack, install, and connect the Cisco uBR7200 series router hardware
that enables your cable television (CATV) headend or distribution hub to support digital data and
Voice-over-IP (VoIP) services. The guide includes procedures to characterize your cable plant to ensure
that data services are reliably supported over the cable infrastructure.

Audience

This guide is intended for cable system installers and technicians who physically install and connect the
Cisco uBR7200 series universal broadband router and associated equipment at the cable headend or
distribution hub. Cable system installers and technicians should be familiar with their cable plant base
operating parameters and service offerings.

The guide provides limited configuration information. After following applicable procedures in this
guide, refer to the

“Obtaining Documentation and Submitting a Service Request” section on page xvii

for related Cisco publications that more completely address configuration.

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

Document Organization

This hardware installation guide is organized into the following chapters and appendixes:

Chapter Title

Description

Chapter 1, “Cisco uBR7200 Series
Overview”

About Cisco uBR7200 series chassis and components.

Chapter 2, “Preparing the
Cisco uBR7200 Series Router for
Installation”

Safety considerations, tools, and other equipment required to prepare your site.

Chapter 3, “Installing the
Cisco uBR7200 Series Router”

Installing the chassis and connecting the power and network interface cables.

Chapter 4, “Connecting the
Cisco uBR7200 Series Router to the
Cable Headend”

Connecting the Cisco uBR7200 series router to a hybrid fiber-coaxial (HFC)
network and describe configuring and measuring downstream and upstream
portions of the HFC network.

Chapter 5, “Maintaining the
Cisco uBR7200 Series Router”

Basic hardware maintenance instructions.

Chapter 6, “Troubleshooting”

Troubleshooting hardware installations.

Appendix A, “Cisco uBR7200 Series
Router Specifications”

System specifications.

Appendix B, “RF Specifications”

Recommended RF settings at the headend for both Data-over-Cable Service
Interface Specifications (DOCSIS) and EuroDOCSIS networks.

Appendix C, “Cable Specifications”

Cable and cable pinout information for the Cisco uBR7200 series routers.

Appendix D, “Industry-Standard Wiring
Plans”

The telephone industry color-code schemes for 25-pair wires including the pin
numbers, optical fibers, and small wire pairs.

«
...
8
9
10
11
12
...
»

Содержание 7246 - uBR Router















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7246 - uBR Router

Бренд: 2N Страницы: 11

Бренд: 2N Страницы: 5

Бренд: 2N Telekomunikace Страницы: 24

Бренд: Qlogic Страницы: 2

Бренд: Qlogic Страницы: 172

Бренд: X-Micro Страницы: 74

Бренд: ZyXEL Communications Страницы: 2

Бренд: Omega Engineering Страницы: 34

Бренд: Taiwan Commate Computer Inc. Страницы: 29

MasterBus Tanklevel Interface

Бренд: Mastervolt Страницы: 8

Anybus Communicator ABC4021

Бренд: HMS Networks Страницы: 60

PISO-725 Series

Бренд: ICP DAS USA Страницы: 8

Бренд: FDI Страницы: 2

Бренд: Z-Com Страницы: 18

Бренд: Patton electronics Страницы: 2

Slideaway CL1008

Бренд: ATEN Страницы: 77

Бренд: ICP DAS USA Страницы: 31

HomePNA PCI Adapter

Бренд: City-Netek Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды