Cisco 7246 - uBR Router Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 238

background image

1-22

Cisco uBR7200 Series Universal Broadband Router Hardware Installation Guide

OL-5421-03

Chapter 1 Cisco uBR7200 Series Overview

Hardware Component Descriptions

These documents are available on Cisco.com at the following URL:

http://www.cisco.com/univercd/cc/td/doc/product/cable/cab_rout/cfig_nts/index.htm

These documents are also available on the Documentation DVD-ROM.

A handle on the AC-input and DC-input power supply units provides a grip point for removing and
replacing the power supply. (

Figure 1-9 on page 1-22

shows the faceplate of the AC-input power supply.

Figure 1-10 on page 1-23

shows the faceplate of the DC-input power supply.) Two captive installation

screws secure the power supply to the chassis and seat the power supply in the router midplane. A Power
OK LED indicates that the power supply is deli5 VDC to the router midplane.

The AC-input power supply has a receptacle for an AC-input power cable. A modular power cable
connects the AC-input power supply to the site AC power source. A cable-retention clip secures the
power cable to the AC-input power supply.

Note

The AC-input power supply has an electrical current rating of 7A for the Cisco uBR7246 and Cisco
uBR7246VXR routers.

Figure 1-9

Cisco uBR7246 and Cisco uBR7246VXR AC-Input Power Supply

The DC-input power supply has a receptacle for two DC-input power leads. Three M5 grounding
receptacles are located on the front of the DC-input faceplate to provide connection for a ground lead.
A ground lead should be installed on two of the receptacles; using either the two receptacles that are
aligned vertically or the two receptacles that are aligned horizontally. A cover is attached to two
strain-relief studs on the power supply faceplate to secure the DC-input power leads running behind the
cover.

Note

Each DC-input power supply has an electrical current rating of 14A, 700 VA. Use a minimum of
12 AWG (4 mm

2

) wire for the input to each DC-input power supply.

Caution

The power input must be protected by a 20A circuit breaker or fuse that is in compliance with your local
electric regulations.

H10074

Cable-retention clip

Power switch

Handle

AC-input receptacle

Captive installation screw

«
...
38
39
40
41
42
...
»

Содержание 7246 - uBR Router















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7246 - uBR Router

Бренд: ZETR Страницы: 2

Бренд: CallDirect Страницы: 33

Бренд: Data Translation Страницы: 60

Бренд: H3C Страницы: 21

Бренд: Compaq Страницы: 112

RouterBOARD SXT 5HnD

Бренд: MikroTik Страницы: 2

iW-RainboW-G30D

Бренд: iWave Страницы: 89

Бренд: Vivotek Страницы: 170

Бренд: Xilica Audio Design Страницы: 30

Бренд: Genie Страницы: 15

Бренд: WHOOP Страницы: 26

Бренд: Fracarro Страницы: 12

MultiConnect SE MTS2EA

Бренд: Multitech Страницы: 2

Бренд: N.A.T. Страницы: 32

Бренд: Telex Communications Страницы: 28

IntroSpect Analyzer 2 Series

Бренд: Aruba Страницы: 5

Бренд: M86 Security Страницы: 309

Бренд: Kramer Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды