Cisco 7246 - uBR Router Скачать руководство пользователя страница 163 | Manualshive

Страница: 163 / 238

background image

5-13

Cisco uBR7200 Series Universal Broadband Router Hardware Installation Guide

OL-5421-03

Chapter 5 Maintaining the Cisco uBR7200 Series Router

Flash Memory Card

The reformatting procedure assumes the following:

•

You have already booted your Cisco uBR7200 series router.

•

You have access to a TFTP server (meaning that you know its name and have connectivity to it) and
at least one interface is available over which you can access this server or to a secondary flash
memory card.

Note

To ensure access to a TFTP server, you must configure at least one network interface on your
Cisco uBR7200 series router. For instructions on using this procedure, refer to the

Cisco uBR7200 Series

Software Configuration Guide

at the following URL:

http://www.cisco.com/en/US/docs/cable/cmts/ubr7200/configuration/guide/cr72scg.html

•

You know the filename of the image you want to copy to the TFTP server or onto the secondary flash
memory card.

To reformat a flash memory card:

Step 1

Insert the flash memory card into slot 0. (If slot 0 is not available, use slot 1.) Refer to the

“Installing a

Flash Memory Card” section on page 5-7

.

Step 2

Copy all the files on the flash memory card to a TFTP server or a secondary flash memory card. The
following example is for copying files to a TFTP server. Refer to the

“Copying a Bootable Image onto a

Flash Memory Card” section on page 5-10

for flash memory card examples.

Router>

enable

Password: <

password

>

Router#

copy slot0:image.name tftp

Enter destination file name [image.name]:

image.name

CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC

Address or name of remote host [tftp.server.name]?

tftp.server.name

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Router#

Step 3

To reformat the flash memory card, use the

format slot0:

(or

format slot1:

) command as follows:

Router#

format slot0:

All sectors will be erased, proceed? [confirm]

Enter volume id (up to 30 characters):

MyNewCard

Formatting sector 1

Format device slot0 completed

Router#

Step 4

Copy the files you saved to the TFTP server back to the flash memory card as follows:

Router#

copy tftp slot0

Enter source filename:

image.name

20575008 bytes available on device slot0, proceed? [confirm]

address or name of remote host [tftp.server.name]?

tftp.server.name

loading new.image from tftp.server.name (via Ethernet1/0):!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

[OK - 7799951/15599616 bytes]

CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC

Router#

The flash memory card is now reformatted and ready to use.

«
...
161
162
163
164
165
...
»

Содержание 7246 - uBR Router















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7246 - uBR Router

Бренд: 3Com Страницы: 48

Бренд: Patton electronics Страницы: 2

Бренд: Patton electronics Страницы: 86

Бренд: Raritan Страницы: 4

Бренд: BSS Audio Страницы: 20

Бренд: Reeven Страницы: 2

Linear SCP-LT8362-S-EVALZ

Бренд: Analog Devices Страницы: 8

Surround Dongle

Бренд: Sennheiser Страницы: 18

StorageWorks AIT 35GB AutoLoader

Бренд: Compaq Страницы: 4

Бренд: 3Com Страницы: 50

Бренд: 4G Systems Страницы: 2

Бренд: ETAS Страницы: 82

Бренд: Belkin Страницы: 2

Бренд: Rainbow Страницы: 2

EtherLink 3C905C-TX

Бренд: 3Com Страницы: 96

Бренд: Intercoax Страницы: 2

Бренд: TP-Link Страницы: 37

Бренд: Wyse Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды