Cisco 7246 - uBR Router Скачать руководство пользователя страница 161 | Manualshive

Страница: 161 / 238

background image

5-11

Cisco uBR7200 Series Universal Broadband Router Hardware Installation Guide

OL-5421-03

Chapter 5 Maintaining the Cisco uBR7200 Series Router

Flash Memory Card

When the system reloads, it boots the new.image file from the flash memory card.

Note

In the preceding example, the exclamation points (!!!) appear as the file is downloaded, and the
“C” characters signify calculation of the checksum, which is a verification that the file has been
correctly downloaded to the flash memory card.

Copying Bootable Images Between Flash Memory Cards

As future releases of Cisco IOS images become available, you will receive these images as a file booted
from a network server, a file on floppy disk, or a file on a flash memory card.

The following scenario describes how to use a newly released image on a flash memory card in a system
that has an older image on a flash memory card in slot 0 and a default boot image in the onboard flash
memory SIMM.

Note

This scenario assumes that the new image will fit on the flash memory card in slot 0, with the old image.

For this scenario, the filenames are as follows:

•

The new image on the new flash memory card is new.image.

•

The old image on the flash memory card in slot 0 is old.image.

•

The bootable image in onboard flash memory is boot.image.

You will copy the new image from the new flash memory card onto the flash memory card that contains
the old image.

Not Enough Memory on the Flash Memory Card

If there is not enough available space on the flash memory card do the following:

Step 1

Use the

delete

command to delete files from the flash memory card to make sufficient room for the new

image; however, do

not

delete the old.image

file.

Step 2

Use the

squeeze

command to remove the deleted files from the flash memory card.

Step 3

If, after you have deleted files and used the

squeeze

command, the two files cannot coexist on the flash

memory card in slot 0:

a.

Remove this card (place it in an antistatic bag and store it in a safe place).

b.

Insert the new flash memory card (with the file new.image) in slot 0.

c.

Proceed to Step 5 of the

“Adding a New Image to the Flash Memory Card”

and use the

boot system

flash slot0:new.image

command to designate the file new.image as the default boot image.

«
...
159
160
161
162
163
...
»

Содержание 7246 - uBR Router















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7246 - uBR Router

Бренд: N-Tron Страницы: 101

Бренд: D-Link Страницы: 12

Бренд: H3C Страницы: 16

Бренд: H3C Страницы: 24

SuperServer 5019S-L

Бренд: Supermicro Страницы: 61

Бренд: Time domain Страницы: 64

Emulator MCU Board for 38D5 Group M38D59T-RLFS

Бренд: Renesas Страницы: 4

Бренд: Medel Страницы: 28

Бренд: Moxa Technologies Страницы: 36

Бренд: FOR-A Страницы: 2

Бренд: Idis Страницы: 18

Бренд: TANDBERG Страницы: 2

Бренд: Intel Страницы: 54

High-Precision AD/DA Board

Бренд: Waveshare Страницы: 8

Бренд: Airlink101 Страницы: 64

Бренд: ETAS Страницы: 29

HomePNA PCI Adapter

Бренд: City-Netek Страницы: 18

Бренд: Cypress Semiconductor Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды