manualshive.com logo in svg

Cisco 7246 - uBR Router, Руководство по установке оборудования

Cisco 7246 - uBR Router - позволяет эффективно управлять сетями. Подробное описание установки оборудования содержится в Hardware Installation Manual. Бесплатно загружайте руководство с manualshive.com, чтобы узнать, как правильно установить и использовать этот роутер.

Поделиться
Скачать
background image

1-21

Cisco uBR7200 Series Universal Broadband Router Hardware Installation Guide

OL-5421-03

Chapter 1      Cisco uBR7200 Series Overview

  Hardware Component Descriptions

Power Supplies

Caution

To ensure adequate airflow across the Cisco uBR7246VXR and Cisco uBR7246 universal broadband 
routers power supplies, a power supply or a power supply filler plate (with its attached air dam) must be 
installed in each power supply bay.

Note

See 

Appendix A, “Cisco uBR7200 Series Router Specifications,”

 for AC-input power supply system 

power specifications, including input voltage and operating frequency ranges.

The power supply contains a main power switch, OK LED, and either an AC-input power receptacle, or 
two hardwired DC-input power leads and three M5 grounding connectors (depending on the type of 
installed power supply). Adjacent to the lower power supply bay, two M5 chassis grounding receptacles 
provide a chassis ground connection for electrostatic discharge (ESD) equipment or a two-hole 
grounding lug for the AC-input power supplies.

The Cisco uBR7246VXR and Cisco uBR7246 support an optional, second power supply for load sharing 
and power redundancy. If you purchased a Cisco uBR7246VXR or Cisco uBR7246 and you want to 
install a second power supply, you must order the second power supply separately. 

Detailed instructions for handling and replacing the Cisco uBR7200 series universal broadband router 
power supplies are contained in the documents:

  •

Cisco uBR7200 Series Universal Broadband Router AC Power Supply Replacement Instructions

 

  •

Cisco uBR7200 Series Universal Broadband Router 550-Watt DC-Input Power Supply Replacement 
Instructions

. 

PA-POS-OC3SMI—1-port OC3 single-mode, 
intermediate reach port adapter

12.0(1)T, 12.1(1a)T1, 

 

12.1 EC

12.0(7)T, 12.1(1a)T1, 

 

12.1 EC

PA-POS-OC3MM—1-port POS OC3 
multimode port adapter

12.0(1)T, 12.1(1a)T1, 

 

12.1 EC

12.0(7)T, 12.1(1a)T1, 

 

12.1 EC

Dynamic Packet Transport (DPT)

PA-SRP-OC12SMX—2-port SRP

8

 OC12 

single-mode, extended reach port adapter

12.1(1a)T, 12.1 EC

12.1(1a)T1, 12.1 EC

1.

To use a PA-4E 4-port Ethernet 10Base-T port adapter in a Cisco uBR7246VXR router, be sure that you have the minimum required hardware revision 
(version 1.14, part number 800-02070-04) or a more recent version of the port adapter.

2.

To use a PA-8E 8-port Ethernet 10Base-T port adapter in a Cisco uBR7246VXR router, be sure that you have the minimum required hardware revision 
(version 1.14, part number 800-02069-04) or a more recent version of the port adapter.

3.

The Gigabit Ethernet port adapter must be combined with the appropriate optical fiber cable and a Gigabit Interface Converter (GBIC).

4.

To use a PA-H 1-port HSSI port adapter in a Cisco uBR7246VXR router, be sure that you have the minimum required hardware revision (version 1.17, 
part number 800-02747-06) or a more recent version of the port adapter.

5.

To use a PA-2H 2-port HSSI port adapter in a Cisco uBR7246VXR router, be sure that you have the minimum required hardware revision (version 1.3, 
part number 800-03306-02) or a more recent version of the port adapter.

6.

CES = circuit emulation service

7.

CBR = constant bit rate

8.

SRP = Spatial Reuse Protocol

Table 1-3

Cisco uBR7200 Series Port Adapter, Chassis, and Cisco IOS Release Compatibility (continued)

Product Number 

Cisco uBR7246 Cisco 

uBR7246VXR

Содержание 7246 - uBR Router















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7246 - uBR Router

D-Link DSR-500 User Manual preview
DSR-500
Бренд: D-Link Страницы: 213
3Com 3C410012A - OfficeConnect Remote 531 Access... Getting Started Manual preview
3C410012A - OfficeConnect Remote 531 Access...
Бренд: 3Com Страницы: 72
Teac HD-35NAS User Manual preview
HD-35NAS
Бренд: Teac Страницы: 20
Maple Systems cMT-FHDX Series Installation Instruction preview
cMT-FHDX Series
Бренд: Maple Systems Страницы: 2
NETGEAR Powerline 100 Installation Manual preview
Powerline 100
Бренд: NETGEAR Страницы: 2
JUMO iTRON B 70.2040 Operating Instructions Manual preview
iTRON B 70.2040
Бренд: JUMO Страницы: 41
Supermicro AOC-MGP-i2 User Manual preview
AOC-MGP-i2
Бренд: Supermicro Страницы: 27
Kaptia Klever Getting Started preview
Klever
Бренд: Kaptia Страницы: 14
ICP DAS USA I-87K Series User Manual preview
I-87K Series
Бренд: ICP DAS USA Страницы: 31
Ovislink Air Live GW-300R User Manual preview
Air Live GW-300R
Бренд: Ovislink Страницы: 20
SMC Networks EZ Switch SMC-EZ1024FDT Specification Sheet preview
EZ Switch SMC-EZ1024FDT
Бренд: SMC Networks Страницы: 4
Inspired Energy ATA004N Operating Instructions preview
ATA004N
Бренд: Inspired Energy Страницы: 5
SONIX MP5S Plus Writer Quick Manual preview
MP5S Plus Writer
Бренд: SONIX Страницы: 23
DELTA GROUP LOYTEC LIP‑3ECTC Installation Instructions preview
LOYTEC LIP‑3ECTC
Бренд: DELTA GROUP Страницы: 4
Commell MP-6010 User Manual preview
MP-6010
Бренд: Commell Страницы: 17
Hamlet HRDSL108W Quick Installation Manual preview
HRDSL108W
Бренд: Hamlet Страницы: 6
Meridian Meridian 1 Option 11C Mini Technical Reference Manual preview
Meridian 1 Option 11C Mini
Бренд: Meridian Страницы: 546
Dahua Technology VDA-NVR2108W4KS2 User Manual preview
VDA-NVR2108W4KS2
Бренд: Dahua Technology Страницы: 363

Бренды по названию

Популярные бренды

Загрузить еще бренды