Cisco 7246 - uBR Router Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 238

background image

1-18

Cisco uBR7200 Series Universal Broadband Router Hardware Installation Guide

OL-5421-03

Chapter 1 Cisco uBR7200 Series Overview

Hardware Component Descriptions

For detailed information on the cable clock card refer to

Cisco Cable Clock Card for the Cisco

uBR7246VXR Universal Broadband Router

at the following URL:

http://www.cisco.com/en/US/docs/ios/12_1t/12_1t1/feature/guide/natlclck.html

Note

Refer to

Appendix F, “Manufacturers for Headend Provisioning Requirements”

for a list of external T1

component suppliers that Cisco recommends.

Cisco Port Adapters

The port adapters serve as a WAN interface and connect directly to the Cisco uBR7200 series universal
broadband router’s midplane. Port adapters installed in the Cisco uBR7200 series support OIR. For a
complete list of port adapters supported in the various Cisco uBR7200 series routers, see

Table 1-3

, refer

to the

Cisco uBR7200 Series Software Configuration Guide,

or the latest Cisco IOS Release Note.

For the

Cisco uBR7200 Series Software Configuration Guide,

go to the following URL:

http://www.cisco.com/en/US/docs/cable/cmts/ubr7200/configuration/guide/cr72scg.html

For Cisco IOS Release Notes, go to the following URL:

http://www.cisco.com/en/US/products/hw/cable/ps2217/prod_release_notes_list.html

For port adapter and HSSI installation information, see the port adapter configuration notes at the
following URL:

http://www.cisco.com/en/US/docs/interfaces_modules/port_adapters/install_upgrade/cables_and_atten
uator/hssi_cable_install/HSSIcab.html

Caution

To ensure adequate airflow across the router’s port adapters, a port adapter or a blank port adapter must
be installed in each port adapter slot.

Cisco Port Adapter-Chassis-Release Matrix

Table 1-3

lists current Cisco uBR7200 series port adapters and identifies the chassis and release trains

on which the port adapter is supported.

Table 1-3

Cisco uBR7200 Series Port Adapter, Chassis, and Cisco IOS Release Compatibility

Product Number

Cisco uBR7246

Cisco uBR7246VXR

Ethernet

PA-4E—4-port Ethernet 10Base-T port adapter

11.3(8)NA, 12.0(1)T, 12.0(6)SC,
12.1(1a)T1, 12.1 EC

12.0(7)SC, 12.0(7)T, 12.1(1a)T1

1

,

12.1 EC

PA-8E—8-port Ethernet 10Base-T port adapter

11.3(8)NA, 12.0(1)T, 12.0(6)SC,
12.1(1a)T1, 12.1 EC

12.0(7)SC, 12.0(7)T, 12.1(1a)T1

2

,

12.1 EC

PA-FE-FX—1-port 100Base-FX Fast Ethernet
port adapter

11.3(8)NA, 12.0(1)T, 12.0(6)SC,
12.1(1a)T1, 12.1 EC

12.0(7)SC, 12.0(7)T, 12.1(1a)T1,
12.1 EC

PA-FE-TX—1-port 100Base-TX Fast Ethernet
port adapter

11.3(8)NA, 12.0(1)T, 12.0(6)SC,
12.1(1a)T1, 12.1 EC

12.0(7)S, 12.1(1a)T1C, 12.0(7)T,
12.1 EC

«
...
34
35
36
37
38
...
»

Содержание 7246 - uBR Router















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7246 - uBR Router

Бренд: XMG Страницы: 5

Бренд: Habitat Страницы: 48

Бренд: NAD Страницы: 2

Бренд: SAF Страницы: 30

Бренд: XESS Страницы: 23

Бренд: Commell Страницы: 36

Scorpio WD2500BPVT

Бренд: Western Digital Страницы: 3

Scorpio WD2500BPVT

Бренд: Western Digital Страницы: 4

HHM Series HHM2411

Бренд: TDK Страницы: 2

Бренд: ebm-papst Страницы: 11

Бренд: YASKAWA Страницы: 15

Бренд: DAD Страницы: 16

Бренд: Addonics Technologies Страницы: 1

Бренд: Grundig Страницы: 24

Бренд: CyberTAN Страницы: 67

HiGain H2TU-R-402 List 7A

Бренд: ADC Страницы: 7

Бренд: Renesas Страницы: 28

Бренд: NKE Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды