Cisco 7246 - uBR Router Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 238

background image

2-11

Cisco uBR7200 Series Universal Broadband Router Hardware Installation Guide

OL-5421-03

Chapter 2 Preparing the Cisco uBR7200 Series Router for Installation

Provisioning the Cable Headend

Verifying the Shipping Container Contents

Step 1

Verify that the following are included in the shipping container (the accessories box might be separate):

•

One Cisco uBR7200 series universal broadband router chassis containing all of the components you
ordered for your system (except the rack-mount and cable-management kit)

•

One or more accessories boxes (some or all might be shipped separately)

Step 2

Check the contents of the accessories box against the “Installation Checklist” and the packing slip to
verify that you received all listed equipment, which should include the following:

•

One modular power cable for an AC-input power supply. (If you purchased a Cisco uBR7246VXR,
or Cisco uBR7246 router with a redundant power supply, you should receive two power cables.)

•

One rack-mount and cable-management kit (3 brackets and 16 mounting screws) for the
Cisco uBR7246VXR and Cisco uBR7246 routers and two rack-mount and cable-management kits.

•

Optional equipment that you ordered, such as network interface cables, transceivers, or special
connectors.

•

CNR or CSRC provisioning documentation, or both.

•

Cisco IOS software documentation, if ordered.

Step 3

Verify that the port adapters installed in your Cisco uBR7200 series router match the port adapter types
on the packing list.

Step 4

Verify that the number of cable interface cards installed in your Cisco uBR7200 series router matches
the number of cable interface cards that you ordered.

Step 5

Refer to

Appendix G, “Site Log,”

then to the

“Cisco uBR7200 Series Chassis Rack-Mounting Options”

section on page 3-2

to begin the installation.

Provisioning the Cable Headend

This section describes the necessary preparations to make at the cable headend before you install the
Cisco uBR7200 series universal broadband router.

Two-Way Data and VoIP

To prepare for two-way data operation, including digitized voice and fax, ensure that the following
conditions are met:

•

The cable headend equipment is properly aligned and certified for two-way transmission based on
procedures provided by the manufacturers of the equipment and in accordance with DOCSIS or
EuroDOCSIS RF Interface Specifications.

•

The cable headend is wired for narrowcast downstream data transmission.

•

The cable headend is wired to supply an RF feed from the upstream fiber-optic receivers to the

Cisco uBR7200 series router.

•

Upstream frequencies are allocated for data transmission.

•

Upstream impairments are measured and understood, and comply with recommendations in
DOCSIS or EuroDOCSIS RF Interface Specifications.

«
...
55
56
57
58
59
...
»

Содержание 7246 - uBR Router















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7246 - uBR Router

SAFETank Series

Бренд: Raidon Страницы: 49

Бренд: H3C Страницы: 21

BroadLink SP3353

Бренд: MicroNet Страницы: 66

Бренд: RAK Страницы: 30

Бренд: Dolphin Страницы: 9

Бренд: TP-Link Страницы: 110

Бренд: insys icom Страницы: 4

Бренд: Valcom Страницы: 4

Бренд: Baicells Страницы: 10

Бренд: Kaptia Страницы: 14

Бренд: Aaeon Страницы: 72

Vocal Performer VE-20

Бренд: Boss Страницы: 20

Бренд: ACTi Страницы: 14

XC-16CH-NVR-4TB

Бренд: Xyclop Страницы: 19

Бренд: Patton electronics Страницы: 8

Бренд: LevelOne Страницы: 49

Air Live GW-300R

Бренд: Ovislink Страницы: 20

EZ Switch SMC-EZ1024FDT

Бренд: SMC Networks Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды