Cisco 7246 - uBR Router Скачать руководство пользователя страница 76 | Manualshive

Страница: 76 / 238

background image

3-8

Cisco uBR7200 Series Universal Broadband Router Hardware Installation Guide

OL-5421-03

Chapter 3 Installing the Cisco uBR7200 Series Router

Installing the Brackets on the Chassis

Step 3

Thread four M4 x 6-mm Phillips flathead screws through the rack-mount bracket and into the side of the
chassis. Use a number 2 Phillips screwdriver to tighten the screws.

Step 4

Repeat

Step 1

through

Step 3

for the other rack-mount bracket.

Step 5

If you plan to include the cable-management bracket in your rear rack-mount configuration, align the
bracket with the four right front-side holes.

Note

The cable-management bracket must be installed on the right side of the Cisco uBR7246 and

Cisco uBR7246VXR chassis when viewed from the front.

Step 6

Thread two four M3 x 6-mm Phillips panhead screws through the cable-management bracket and into
the chassis, and tighten the screws.

This completes the procedure for installing the rack-mount brackets and the cable-management bracket
on the chassis for a rear rack-mount configuration. Proceed to the

“Installing the Chassis in the Rack”

section on page 3-11

.

Caution

To prevent injury, review the safety precautions in

Chapter 2, “Preparing the Cisco uBR7200 Series

Router for Installation,”

before installing the universal broadband router in a rack.

Installing Rack-Mount Brackets on the Front of the Chassis

To install the rack-mount brackets on the chassis for a front rack-mount configuration, complete the
following steps:

Note

If you plan to use the cable-management bracket in your rack-mount configuration for the

Cisco uBR7246 and Cisco uBR7246VXR, you must install your rack-mount brackets on the rear of the
chassis. Proceed to the

“Installing Rack-Mount Brackets on the Rear of the Chassis” section on page 3-7

.

Step 1

Locate the threaded holes in the front sides of the chassis.

Step 2

If you want the front of the chassis flush with the front of the rack, align the first rack-mount bracket to
the threaded holes in the right side of the chassis as shown in

Figure 3-9 on page 3-9

.

If you want the front of the chassis protruding from the rack, align the first rack-mount bracket to the
threaded holes in the right side of the chassis as shown in

Figure 3-10 on page 3-9

.

Note

There are eight holes in each of the rack-mount brackets for the Cisco uBR7246VXR and
Cisco uBR7246 chassis. You may use either set of four holes to align the bracket to the threaded holes
in the sides of the chassis.

«
...
74
75
76
77
78
...
»

Содержание 7246 - uBR Router















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7246 - uBR Router

All in One Printer

Бренд: Baracoda Страницы: 42

Бренд: ZETR Страницы: 2

Бренд: CallDirect Страницы: 33

Бренд: Paradox Страницы: 4

Бренд: PaloAlto Networks Страницы: 2

Бренд: Paradyne Страницы: 112

Бренд: Cambium Networks Страницы: 215

Wisenet PRN-6400B4

Бренд: Hanwha Techwin Страницы: 14

Бренд: ZALMAN Страницы: 9

Бренд: Lucent Technologies Страницы: 20

AAA-130SA SERIES

Бренд: Adaptec Страницы: 94

Бренд: 1&1 Страницы: 32

WNFB-265AXI(BT)

Бренд: Sparklan Страницы: 14

Бренд: Arbor Technology Страницы: 8

Бренд: Navitar Страницы: 1

FrameSaver DSL 9788 Router

Бренд: Paradyne Страницы: 28

Бренд: Dataprobe Страницы: 16

Бренд: VideoWave Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды