Cisco 7246 - uBR Router Скачать руководство пользователя страница 80 | Manualshive

Страница: 80 / 238

background image

3-12

Cisco uBR7200 Series Universal Broadband Router Hardware Installation Guide

OL-5421-03

Chapter 3 Installing the Cisco uBR7200 Series Router

Installing the Brackets on the Chassis

To install the chassis in the rack complete the following steps:

Step 1

On the chassis, ensure that all captive installation screws on the network processing engine, the I/O
controller, each cable interface card, and each power supply are tightened and the port adapter retention
clip is in the locked position.

Step 2

Make sure that your path to the rack is unobstructed. If the rack is on wheels, ensure that the brakes are
engaged or that the rack is otherwise stabilized.

Caution

Two people should perform

Step 3

through

Step 6

.

Step 3

Position the chassis so that the front end is closest to you; then lift the chassis and move it to the rack.
To prevent injury, avoid sudden twists or moves.

Step 4

Slide the chassis into the rack, pushing it back until the brackets (installed at the front or rear of the
chassis) meet the mounting strips or posts on both sides of the equipment rack.

Note

The rack-mount bracket must be placed behind the rack post or mounting strip in the rear installation
configuration. (See

Figure 3-2 on page 3-4

.)

Step 5

While keeping the brackets flush against the posts or mounting strips, position the Cisco uBR7200 series
so that the holes in the brackets are aligned with those in the mounting strips.

Step 6

Insert the 10/32 x 3/8 slotted screws (two to a side) through the brackets and into the mounting strip (use
the top and bottom bracket holes, shown in

Figure 3-2 on page 3-4

,

Figure 3-3 on page 3-4

,

Figure 3-4

on page 3-5

, and

Figure 3-5 on page 3-5

). Using a 7/16-inch, flat-blade screwdriver, tighten all the

screws.

This completes the procedure for installing the chassis in the rack. Proceed to the

“Cabling” section on

page 3-14

to continue the installation.

Warning

To prevent bodily injury when mounting or servicing this unit in a rack, you must take special
precautions to ensure that the system remains stable. The following guidelines are provided to
ensure your safety:

Statement 1006

•

This unit should be mounted at the bottom of the rack if it is the only unit in the rack.

•

When mounting this unit in a partially filled rack, load the rack from the bottom to the top with
the heaviest component at the bottom of the rack.

•

If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing
the unit in the rack.

«
...
78
79
80
81
82
...
»

Содержание 7246 - uBR Router















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7246 - uBR Router

Бренд: IBM Страницы: 72

Бренд: Acconeer Страницы: 32

Бренд: Patton electronics Страницы: 51

Бренд: mikroElektronika Страницы: 3

Emulator MCU Board for 38D5 Group M38D59T-RLFS

Бренд: Renesas Страницы: 4

Бренд: Radicom Страницы: 27

PCH1 T P Series

Бренд: Parker Страницы: 107

Бренд: Arduino Страницы: 25

SRA311-008P8 Series

Бренд: Divio Страницы: 4

Бренд: National Instruments Страницы: 80

Бренд: Advantech Страницы: 108

Бренд: Deliberant Страницы: 16

Бренд: Nexxt Страницы: 2

Бренд: Avigilon Страницы: 12

Бренд: rtd Страницы: 28

DotSurfer GPC-2100

Бренд: Gtran Wireless Страницы: 44

Бренд: NetComm Страницы: 4

Бренд: Ruckus Wireless Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды