Troubleshooting
King Edge
6-24
WARNING
Only trained personnel with experience
in electrical or mechanical repair should
troubleshoot and repair the unit.
Troubleshooting
WARNING
Read the
REPAIR
chapter and make
sure that the power is disconnected
before doing any repairs.
ISSUE
POSSIBLE CAUSE
SOLUTION
Laydown of Flatwork is Erratic
1. Mechanical problem with
spread clamp or its air
cylinder.
Check/adjust. Refer to the
REPAIR
chapter,
Spread Section
section,
Spreader Clamp Mechanical Ad-
justment
procedure.
•
2. Air bars out of alignment.
Adjust. Refer to the
REPAIR
chap-
ter,
Compressed Air System
sec-
tion,
Air Bar Alignment
procedure.
•
3. Adjust length of the air bars
blast.
Adjust. Refer to the
CHI PANEL OP-
ERATION
bulletin,
Adjustment
sec-
tion,
CHI Adjustments
procedure.
•
4. CORNER STOP DELAY
settings need adjustment.
Adjust. Refer to the
CHI PANEL
OPERATION
bulletin,
Adjustment
section,
Inlet Section Adjustments
procedure.
•
5. Early air blast occurs as the
corners are detected by the
taut sensors.
Adjust. Refer to the
REPAIR
chap-
ter,
Sensors
section,
Taut Photo-
sensor Alignment
procedure.
•
Flatwork Pieces Overlap
1. GAP settings need adjust-
ment.
Adjust. Refer to the
CHI PANEL OP-
ERATION
bulletin,
Adjustment
sec-
tion,
CHI Adjustments
procedure.
•
2. Tail sensors may be dirty,
misaligned, or defective.
Clean/adjust/replace as necessary.
For more information within this
chapter, refer to
Sensor Function
section.
•
Leading Edge of Flatwork
Folded Over
1. The corners are too long.
Check sensor alignment in front of
clutch rolls. Refer to the
REPAIR
chapter,
Sensors
section,
Roll Pho-
tosensor Alignment
procedure.
Adjust CORNER STOP DLY. Refer
to the
CHI PANEL OPERATION
bulletin,
Adjustment
section,
Inlet
Adjustments (INL)
procedure.
•
•
2. Mechanical problem with
the spread clamp or its air
cylinder.
Check/adjust. Refer to the
REPAIR
chapter,
Spread Section
section,
Spreader Clamp Mechanical Ad-
justment
procedure.
•
3. CORNER STOP DELAY
settings need adjustment.
Adjust. Refer to the
CHI PANEL
OPERATION
bulletin,
Adjustment
section,
Inlet Section Adjustments
procedure.
•
6.8 Discharge Section
Содержание King Edge
