ENGINE 6-33
5. Lubricate the lip of a new seal with engine oil. Keep
oil off the parting line surface. Gradually push with
a hammer handle, while turning crankshaft, until
seal is rolled into place. (Similar to installing a
main bearing.) Be careful that seal tangs at parting
line do not cut bead on back of seal.
6. Install the rear main bearing cap (with new seal) and
torque to specifications.
Torsional Damper
Rem oval
1. Remove fan belt, fan and pulley.
2. Remove the radiator and shroud assembly as
outlined in Section 13.
NOTE:
If additional operations (such as cam
shaft removal) are not being performed, the ra
diator removal will not be necessary on vehicles
using the 366, 396 and 427 cu. in. engines.
3. Remove accessory drive pulley then, if so equipped,
remove damper retaining bolt.
4. Install Tool J-6978 on damper then, turning puller
screw, remove damper (fig. 9V).
NOTE:
Tool J-6978 has holes forming two pat
terns. A two bolt and a three bolt pattern. The
holes for the two bolt pattern must be elongated
for use on the 366 and 427 cu. in. engines.
Installation
C A U TIO N :
The inertia weight section of the
torsional damper is assembled to the hub with
a rubber type material. The installation pro
cedures (with proper tool) must be followed or
movement of the inertia weight section on the
hub will destroy the tuning of the torsional
damper.
1. Coat front cover seal contact area (on damper) with
engine oil.
2. Install damper on crankshaft as follows:
307 and 327 cu. in. ENGINE
a. Attach damper installer Tool J- 22197 on damper
then adjust fingers of tool to prevent inertia
weight moving (fig. 10V).
b. Position damper in alignment with crankshaft
keyway then drive into position (fig. 34) (until it
bottoms on crankshaft sprocket) and remove tool
from balancer.
366, 396 and 427 cu. in. ENGINE
F ig . 10V—In stalling Torsional Damper
a. Place damper in position over key on crankshaft.
b. Using Tool J -21058 pull torsional damper onto
crankshaft (fig. 11V).
NOTE:
If radiator has not been removed from
the vehicle a 1/2"-20 x 5" bolt and a 1/2"-20
nut may be used in place of the bolt and nut
from Tool J -21058.
CA U TIO N :
Install bolt in crankshaft with suf
ficient thread engagement (min. 1/2").
F ig . 1I V —In stalling Torsional Damper (366, 396 & 427)
CHEVROLET TRUCK SERVICE MANUAL
Содержание 10 Series 1968
