Celli Brave 30 ES Скачать руководство пользователя

Страница: 55 / 68

Troubleshooting

Brave 30 ES- Brave 60 ES - Brave 90 ES

7 - Troubleshooting

PROBLEM

PROBABLE CAUSE

REMEDIES

The dispenser does not start up

Power supply failure

Check that power is present.
If the power is OK, call an authorised
technician.

Thermostat failure

Call an authorised technician

The cooling unit operates

continually, and the water

delivered is warm

Refrigerant gas leak

Call an authorised technician

The cooling unit operates

continually, and the water freezes

Thermostat failure

Call an authorised technician

Noisy water pump

Water supply failure

Check that water is reaching the
appliance

The dispenser does not deliver

water

Main water tap turned off

Turn on the water tap

Water supply connection tube crushed
or obstructed

Inspect the path of the tube

No electricity supply

Check the plug is well inserted

The dispenser does not deliver

sparkling water

cylinder has run out

Replace the CO

cylinder

Electronic control unit malfunction

Call an authorised technician

Pump failure

Call an authorised technician

cylinder shut off

Open the CO

cylinder valve

The dispensed product is not cold

enough

The ice bank has run out

Wait until the ice bank has fully
reformed

The water entering the machine is too
hot

Check the incoming water temperature
is lower than 32°C

Soda recirculation pump malfunction

Call an authorised technician

Inadequate insulation on the python

Call an authorised technician

Only water is dispensed

The syrups have run out

Replace the syrup tanks with new ones

The syrup lines are obstructed

Sanitise the syrup lines, as indicated in
the relevant paragraph

No CO

Replace the CO

cylinder

FOR ANY OTHER PROBLEMS NOT COVERED HERE,

CONTACT THE SERVICE CENTRE

Содержание Brave 30 ES





































































Результаты поиска

Содержание Brave 30 ES

Отзывы:

Похожие инструкции для Brave 30 ES

Бренды по названию

Популярные бренды

Celli Brave 30 ES, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Brave 30 ES

Отзывы:

Похожие инструкции для Brave 30 ES

Бренды по названию

Популярные бренды