CARLO GAVAZZI VariFlex3 RVFFA3400400F Скачать руководство пользователя страница 8

Страница: 8 / 99

Motor Controllers AC Variable Frequency Drives

Type Variflex

RVFF

Specifications are subjected to change without notice.

1.6 Maintenance, Inspection and Replacement

Warning

➢

Ensure a minimum delay of 5 minutes after power has been turned OFF before starting

an inspection. Also confirm that the charge light is OFF and that the DC bus voltage

has dropped below 25Vdc. Ensure a minimum delay of 15 minutes while inverter is over

20HP.

➢

Never touch high voltage terminals in the inverter.

➢

Ensure that the power to the inverter is disconnected before disassembling the inverter.

➢

Only authorized personnel should perform maintenance, inspection, and replacement

operations. (Remove any metal jewellery such as watches and rings and use insulated

tools).

Caution

➢

The Inverter can be used in an environment with a temperature range from 14° to +104°F

(-10 to +40°C) and relative humidity of 95% non-condensing.

➢

The inverter must be operated in a dust, gas, mist and moisture free environment.

1.7 Disposal of the Inverter

Caution

➢

Please dispose of this unit with care as an industrial waste and according to your

required local regulations.

➢

The capacitors of inverter main circuit and printed circuit board are considered as

hazardous waste and must not be burned.

➢

The plastic enclosure and parts of the inverter such as the top cover board will release

harmful gases if burned.

WEEE designation

Do not dispose of the product together with the household waste but according
to the disposal regulations for electronic waste locally applicable at the product
installation site.

Содержание VariFlex3 RVFFA3400400F




































































































Результаты поиска

Содержание VariFlex3 RVFFA3400400F

Отзывы:

Бренды по названию

Популярные бренды

CARLO GAVAZZI VariFlex3 RVFFA3400400F, Быстрый старт

Результаты поиска

Содержание VariFlex3 RVFFA3400400F

Отзывы:

Бренды по названию

Популярные бренды