CARLO GAVAZZI VariFlex3 RVFFA3400400F Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 99

CARLO GAVAZZI VariFlex3 RVFFA3400400F Скачать руководство пользователя страница 12

Motor Controllers AC Variable Frequency Drives

Type Variflex

3

RVFF

Specifications are subjected to change without notice.

11

3.2 Considerations for peripheral equipment

Power Supply

MCC

B

Molded

Circuit

Breaker

Magnetic

Contactor

AC

Reactor

Fast

Acting

Fuse

Input Noise

Filter

F510

Inverter

Ground

Induction

Motor

Ground

Output Noise

Filter

~

~

~

Power supply:

⚫

!

Ensure that the correct voltage is applied to avoid damaging the

inverter.

Molded-case circuit breaker (MCCB) or fused disconnect:

⚫

A molded-case circuit breaker or fused disconnect must be installed
between the AC source and the inverter that conforms to the rated
voltage and current of the inverter to control the power and protect the
inverter.

⚫

!

Do not use the circuit breaker as the run/stop switch for the

inverter.

Ground fault detector/breaker:

⚫

!

Install a ground fault breaker to prevent problems caused by

current leakage and to protect personnel. Select current range up to
200mA, and action time up to 0.1 second to prevent high frequency
failure.

Magnetic contactor:

⚫

Normal  operations  do  not  need  a  magnetic  contactor.  When
performing  functions  such  as  external  control  and  auto  restart  after
power  failure,  or  when  using  a  brake  controller,  install  a  magnetic
contactor.

⚫

!

Do not use the magnetic contactor as the run/stop switch for

the inverter.

AC line reactor for power quality:

⚫

When  inverters  are  supplied  by  a  high  capacity  power  source  (>
600KVA),  an  AC  reactor  can  be  installed  on  the  input  side  of  the
inverter to improve the power factor.

Install Fast Acting Fuse:

⚫

To protect peripheral equipment, install fast acting fuses in
accordance with the specifications in section

11.4 for peripheral

devices.

Input Noise filter:

⚫

A filter must be installed when there are inductive loads affecting the
inverter. The inverter meets EN55011 Class A, category C3 when the
Carlo Gavazzi special filter is used. See section 11.3 for peripheral
devices.

Inverter:

⚫

Output terminals T1, T2, and T3 are connected to U, V, and W
terminals of the motor. If the motor runs in reverse while the inverter
is set to run forward, swap any two terminals connections for T1, T2,
and T3.

⚫

!

To avoid damaging the inverter, do not connect the output

terminals T1, T2, and T3 to AC input power.

⚫

!

Connect the ground terminal properly. (400V series: Rg <10



.)

Output Noise filter:

⚫

An output noise filter may reduce system interference and induced
noise.

Motor:

⚫

If the inverter drives multiple motors the output rated current of the
inverter must be greater than the total current of all the motors.

RVFF

«
...
10
11
12
13
14
...
»

Содержание VariFlex3 RVFFA3400400F




































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды