Canon iR3245, Руководство по обслуживанию

Страница: 475 / 746

Chapter 16
16-7
16.1.6 E602 (Error in HDD/encryption board)
0019-7875
iR3225 / iR3225N / iR3235 / iR3235N / iR3245 / iR3245N
E5F2 0001 Saddle guide
error The guide home position sensor does not go on when the guide motor has
been driven for 0.455 sec.
Guide motor (M3S)/guide home position sensor (PI13S) Check the guide motor. Check the guide
home position sensor. Replace the finisher
controller PCB. Check the guide drive
mechanism.
0002 The guide home position sensor does not go off when the guide motor has
been driven for 1 sec.
Guide motor (M3S)/guide home position sensor (PI13S)
E5F3 0001 saddle alignment
error The aligning plate home position sensor does not go on when the alignment
motor has been driven for 0.5 sec. (at time of initialization, 1.67 sec.)
Alignment motor (M5S)/aligning plate home position sensor (PI5S) Check the alignment motor. Check the
alignment home position sensor. Check the
aligning plate drive mechanism. Replace the
finisher controller PCB.
0002 The aligning plate home position sensor does not go off when the alignment
motor has been driven for 1 sec.
Alignment motor (M5S)/aligning plate home position sensor (PI5S)
E5F4 0001 Saddle rear
stapling error The stitching home position sensor does not go on when the stitch motor
(rear) has been rotated in reverse for 0.5 sec or more.
Stitch motor (rear; M6S)/stitching home position sensor (rear; MS5S) Replace the stitcher (rear). Check the
harness. Replace the finisher controller PCB.
0002 The stitching home position sensor does not go off when the stitch motor
(rear) has been rotated in normal direction for 0.5 sec or more.
Stitch motor (rear; MS)/stitching home position sensor (rear; MS5S)
E5F5 0001 Saddle front
stapling error The stitching home position sensor does not go on when the stitch motor
(front) has been rotated in reverse for 0.5 sec or more.
Stitch motor (front; M7S)/stitching home position sensor (front; MS7S) Replace the stitcher (front). Check the
harness. Replace the finisher controller PCB.
0002 The stitching home position sensor does not go off when the switch motor
(front) has been rotated in normal direction for 0.5 sec or more.
Stitch motor (front; M7S)/stitching home position sensor (front; MS7S)
E5F6 0001 Saddle butting
error The paper butting plate home position sensor does not go on when the paper
butting plate motor has been driven for 0.3 sec.
Paper butting plate motor (M8S)/paper butting plate home position sensor
(PI14S) Check the paper butting plate motor. Check
the paper butting plate home position sensor.
Replace the finisher controller PCB.
0002 The paper butting plate home position sensor does not go off when the paper
butting plate motor has been driven for 80 msec or more.
Paper butting plate motor (M8S)/paper butting plate home position sensor
(PI14S)
0003 The number of detection pulses of the paper butting plate motor has dropped
below a specific value.
paper butting plate motor (M8S)/paper butting plate motor clock sensor
(PI1S) Check the paper butting plate motor. Check
the paper butting plate motor clock sensor.
Replace the finisher controller PCB.
0004 The paper butting plate leading edge sensor does not go off when the paper
butting plate motor has been driven for 80 msec.
Paper butting plate motor (M8S)/paper butting plate leading edge sensor
(PI15S) Check the paper butting plate motor. Check
the paper butting plate leading edge sensor.
Replace the finisher controller PCB.
0005 The paper butting plate leading edge sensor does not go on when the paper
butting plate motor has been driven for 0.3 sec.
Paper butting plate more (M8S)/paper butting plate leading edge sensor
(PI15S)
E5F8 0001 Saddle connector
error The connector of the paper butting plate home position sensor has been
identified as being disconnected.
Connector of guide home position sensor (PI13S) Connect the connector of the guide home
position sensor. Check the harness. Replace
the finisher controller PCB.
0002 The connector of the paper butting plate home position sensor has been
identified as being disconnected.
Connector of paper butting plate home position sensor (PI14S) Connect the connector of the paper butting
plate home position sensor. Check the
harness. Replace the finisher controller PCB.
0003 The connector of the paper butting plate leading edge sensor has been
identified as being disconnected.
Connector of paper butting plate leading edge sensor (PI15S) Connect the connector of the paper butting
plate leading edge sensor. Check the harness.
Replace the finisher controller PCB.
E5F9 0001 Saddle switch
error The inlet cover switch has been identified as being open for 1 sec or more
after the start of printing or the start of initial rotation with the following
sensors identifying their respective covers as being closed:
- inlet cover sensor (PI9S)
- nt cover open/closed sensor (PI2S)
- delivery cover sensor (PI3S)
Or, the front over switch (MS2S) or the delivery cover switch (MS3S) is open.
Inlet cover switch (MS1S)/front cover switch (MS2S)/delivery cover switch
(MS3S) Check the inlet cover switch. Check the inlet
cover sensor. Check the front cover open/
closed sensor. Check the delivery cover
sensor. Replace the finisher controller PCB.
0002 The front cover switch has been identified as being open from the start of
printing or the start of initial rotation with the following sensors identifying
their respective covers as being closed.
- inlet cover sensor (PI9S)
- front cover open/closed sensor (PI2S)
- delivery cover sensor (PI3S)
- front cover switch (MS2S)/delivery cover switch (MS3S) Check the front cover switch. Check the inlet
cover sensor. Check the front cover open/
closed sensor. Check the delivery cover
sensor. Replace the finisher controller PCB.
0003 The delivery cover switch has been identified as being open after the start of
printing or the start of initial rotation of the host machine with the following
sensors identifying their respective covers as being closed:
- inlet cover sensor (PI9S)
- front cover open/closed sensor (PI2S)
- delivery cover sensor (PI3S)
- delivery cover switch (MS3S) Check the delivery cover switch. Check the
inlet cover sensor. Check the inlet cover
sensor. Check the front cover open/closed
sensor. Check the delivery cover sensor.
Replace the finisher controller PCB.
Code Detail code Name Detection Remedy