Canon iR3245, Руководство по обслуживанию

Страница: 474 / 746

Chapter 16
16-6
E537 0001 Rear alignment
error (External
finisher) The home position sensor does not go on within 2000 msec after the start of
operation when the read aligning plate is moved to home position. Replace the finisher controller PCB. Replace
the rear alignment motor. Check the rear
aligning plate drive mechanism. Check the
rear alignment home position sensor.
0002 The home position sensor does not go off within 1000 msec after the start of
operation when the rear aligning plate is moved form home position.
E540 8002 Stack tray motor
error (Finisher-
S1) The operation to detect the paper surface of the stack tray does not end within
1.0 sec. Replace the finisher controller PCB. Replace
the tray ascent/descent motor. Check the
stack tray drive mechanism. Check the paper
surface sensor.
8003 An abnormal combination of sensor states has been detected. Replace the finisher controller PCB. Check
the stack tray upper limit sensor. Check the
stack tray lower limit sensor. Check the stack
tray upper paper surface sensor. Check the
stack tray lower paper surface sensor.
E540 0002 Upper tray
ascent/descent
motor error
(External
finisher) Upper tray ascent/descent motor clock error Replace the No. 1 tray shift motor. Replace
the finisher controller PCB. Check the tray
ascent/descent mechanism.
0003 Area error Replace the No. 1 tray area sensor PCB.
Replace the finisher controller PCB.
0004 Safety switch activation Check the No. 1 tray closed detecting switch.
Replace the finisher controller PCB.
E542 0002 Lower tray
ascent/descent
motor error
(External
finisher) Lower tray ascent/descent motor clock error Replace the No. 2 tray shift motor. Replace
the finisher controller PCB. Check the tray
ascent/descent mechanism.
0003 Area error Replace the No. 2 tray shift area sensor PCB.
Replace the finisher controller PCB.
E577 8001 Paddle error
(Finisher-S1) The paddle home position sensor does not go on within 1.5 sec when the
paddle is shifted to home position. Check the paddle motor. Check the paddle
home position sensor. Replace the finisher
controller PCB.
8002 The paddle home position sensor does not go off within 1.0 sec when the
paddle is moved to home position.
E584 0001 Shutter unit error
(External
finisher) The shutter open sensor does not go off (i.e., the shutter does not close). Check the stack edging motor. Check the
open/close clutch. Check the shutter home
position sensor. Replace the finisher
controller PCB.
0002 The shutter open sensor does not go on (i.e., the shutter does not open).
E590 0001 Punch motor
error The punching home position is not detected even when the puncher motor has
been driven for 200 msec. Check the punch motor. Check the punch
motor clock sensor. Check the punch driver
PCB. Replace the finisher controller PCB.
0002 The punch home position sensor is not defected even after the motor has
stopped at time of punch motor initial operation.
E591 0001 Punch dust
sensor error Error in light-receiving voltage while light is emitted Check the waste paper case full sensor.
Check the punch driver PCB. Replace the
finisher controller PCB.
0002 Error in light-receiving voltage while light is not emitted
E592 0001 Paper trailing
edge sensor/
horizontal sensor
error Error in light-receiving voltage when light is emitted (trailing edge sensor) Check the paper trailing edge sensor. Check
the horizontal registration sensor. Check the
punch driver PCB. Replace the finisher
controller PCB.
0002 Error in light-receiving voltage when light is not emitted (trailing edge
sensor)
0003 Error in light-receiving voltage when light is emitted (horizontal registration
sensor 1)
0004 Error in light-receiving voltage when light is not emitted (horizontal
registration sensor 1)
0005 Error in light-receiving voltage when light is emitted (horizontal registration
sensor 2)
0006 Error in light-receiving voltage when light is not emitted (horizontal
registration sensor 2)
0007 Error in light-receiving voltage when light is emitted (horizontal registration
sensor 3)
0008 Error in light-receiving voltage when light is not emitted (horizontal
registration sensor 3)
0009 Error in light-receiving voltage when light is emitted (horizontal registration
sensor 4)
000A Error in light-receiving voltage when light is not emitted (horizontal
registration sensor 4)
E593 0001 Punch shift
motor error The light-receiving voltage home position sensor does not go off when light
is emitted. Check the horizontal registration motor.
Check the horizontal registration home
position sensor. Check the punch driver
PCB. Replace the finisher controller PCB.
Check the punch shift mechanism.
0002 The light-receiving voltage home position sensor does not go on when light
is not emitted.
E5F0 0001 Saddle paper
positioning plate
error The paper positioning plate home position sensor does to go on when the
paper positioning motor has been driven for 1.33 sec.
Paper positioning plate motor (M4S)/paper positioning plate home position
sensor (P17S) Check the paper positioning plate motor.
Check the paper positioning plate home
position sensor. Replace the finisher
controller PCB. Check the paper positioning
plate drive mechanism.
0002 The paper positioning plate home position sensor doest not go off when the
paper positioning plate motor has been driven for 1 sec.
Paper positioning plate motor (M4S)/paper positioning plate home position
sensor (P17S)
E5F1 0001 Saddle paper
folding error The number of detection pulses of the paper folding motor clock sensor has
dropped below a specific value.
Paper folding motor (M2S)/paper folding motor clock sensor (P14S) Check the paper folding motor. Check the
paper folding motor clock sensor. Replace
the finisher controller PCB. Check the paper
folding plate drive mechanism.
0002 The state of the paper folding home position sensor doest not change when
the paper folding motor has been driven for 3 sec.
Paper folding motor (M2S)/paper folding motor clock sensor (P14S)
Code Detail code Name Detection Remedy