8
8
8-128
8-128
Service Mode > COPIER > OPTION > IMG-MCON
Service Mode > COPIER > OPTION > IMG-MCON
COPIER > OPTION > IMG-MCON
PASCL-TY
Paper setting for auto gradation adj
Lv.2 Details
Auto gradation adjustment is normally executed with the
recommended paper specified for each location. However, if you
want to change the paper type, use this setting to change the paper
type.
Use case
When executing the auto gradation adjustment using a paper other
than the recommended paper type
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution
Do not change the setting in the normal operation.
Display/adj/set range
1 to 3
1: CS-814 (Except for USA and EU. Mainly for Japan)
2: Hammermill (For USA)
3: Mondi (For EU)
Default value
The value differs according to the location.
AST-SEL
Adj of advanced smoothing effect
Lv.2 Details
To adjust the smoothing effect which is set in the advanced
smoothing UI.
Set 3 if no smoothing effect is obtained even though Strong is set in
the advanced smoothing UI.
Set 0 if too much effect is obtained even though Weak is set in the
advanced smoothing UI.
Use case
When image failures (jaggy, moire) occur
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range
0 to 3
Default value
2
Supplement/memo
AST: Advanced Smoothing Technology
REGM-SEL
Adj of fine-line density correction
Lv.2 Details
To adjust the line and text density which is set in the thin line density
adjustment UI.
Set 4 if density is too low even 2 is set in the thin line
density adjustment UI.
Set 0 if density is too high even though -2 is set in the thin line
density adjustment UI.
Use case
When line and text adjusted by thin line density adjustment is too
dark or too light in the case of 1200 dpi print
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range
0 to 4
Default value
2
Supplement/memo
REGM-SEL: REos GaMma SELect
COPIER > OPTION > IMG-MCON
SCR-SW
Set of low screen ruling dither
Lv.1 Details
To set the dithering method for low screen ruling.
When changing the value, confirm the change by setting “1: Low
screen ruling” in COPIER> TEST> PG> TXPH.
Use case
Upon user’s request (Dot dithering is used)
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Execute Auto Adjust Gradation (Full Adjust).
Display/adj/set range
0 to 1
0: Low screen ruling dot dithering, 1: Low screen ruling dot dithering
(screen ruling lower than 0)
Default value
0
Related service mode
COPIER> TEST> PG> TXPH
ERS-SEL1
Set 1200 dpi ERS process:PS Expnsn Kit
Lv.1 Details
To change the ERS processing when the hue of patterned graphics
is changed according to phase in the case of making 1200-dpi output
with the PS Expansion Kit installed.
The processing is changed only for graphics and images, and ERS
weighting processing is performed to characters even if the setting is
changed.
Set 1 when the aforementioned symptom occurs.
Set 3 if the proportion of small characters is distorted after 1 is set.
Set 5 if the color of graphics is not stabilized after 1 or 3 is set. In this
setting, however, a thin line of a single line disappears.
Use case
When the hue is changed according to phase when making 1200-dpi
output
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range
0 to 7
The following processing are performed to graphics and images
respectively:
0: Max skipping, simple skipping
1: ERS (average), simple skipping
2: ERS (average), ERS (average)
3: ERS (weighting), simple skipping
4: ERS (weighting), ERS (weighting)
5: Simple skipping, simple skipping
6, 7: Not used
Default value
0
ERS-SEL2
Not use
Lv.1 Details
Not use
T-8-45
