7
7
7-64
7-64
Error Code > Error Code > Error Code Details
Error Code > Error Code > Error Code Details
E
Code
Detail
Code
Location
Item
Description
E674 000C 07
Title
FAX Board communication error
Description An error was detected in access of the modem IC or port IC
used by Fax
Remedy
Note: Note: For the part described as the Main Control PCB, it
indicates Main Controller PCB 2 when the FAX Board is for 1
line, and Main Controller PCB 1 when the FAX Board is for 2
lines.
1. Check wire connection between the FAX Board and the Main
Controller PCB
2. Replace the FAX Board
3. Replace the Main Controller PCB
E674 0010 07
Title
FAX Board communication error
Description Error in timer device to be used by FAX at activation
Remedy
Note: For the part described as the Main Control PCB, it
indicates Main Controller PCB 2 when the FAX Board is for 1
line, and Main Controller PCB 1 when the FAX Board is for 2
lines.
Replace the Main Controller PCB
E674 0011 07
Title
FAX Board communication error
Description Error when the timer device to be used by FAX is started
Remedy
Note: For the part described as the Main Control PCB, it
indicates Main Controller PCB 2 when the FAX Board is for 1
line, and Main Controller PCB 1 when the FAX Board is for 2
lines.
Replace the Main Controller PCB
E674 0100 07
Title
FAX Board communication error
Description After completion of fax communication, writing of the
communication information (log) failed, and the log cannot be
read.
Remedy
Turn OFF and then ON the power.
(Points to note) All the previous communication information will
be cleared.
E674 0200 07
Title
HDD access error
Description An error occurred when accessing the HDD.
Remedy
1. Turn OFF and then ON the power.
2. System all format and installation
3. Replace the HDD.
4. Replace the Main Controller PCB 2.
E674 0030 07
Title
FAX Board communication error
Description Checksum error of USB-FAX MAINROM
Remedy
When the power is turned ON, get in the download mode from
service mode to execute downloading of USBFAX MAINROM
E
Code
Detail
Code
Location
Item
Description
E677 0003 00
Title
Print server error
Description Error is detected by checking of the mother board at startup of
the print server
Remedy
1. Check cable connection and turn ON the power again
2. Reinstall the printer server
E710 0001 05
Title
IPC initialization error
Description Unable to be ready within 3 sec after IPC chip was started
Remedy
Check the connection cable between the DC Controller PCB
and the Finisher
E711 0001 05
Title
IPC register error
Description 4 or more errors are set to the error register of the IPC chip in 1.5
sec
Remedy
Check the connection cable between the DC Controller PCB
and the Finisher
E713 0001 05
Title
Finisher communication error 1
Description Continuous interruption to RX communication from the Finisher
(Finisher down is detected)
Remedy
Turn OFF and then ON the main power
E713 0002 05
Title
Finisher communication error 2
Description A large amount of data from the Finisher causes data overflow
Remedy
Turn OFF and then ON the main power
E713 0003 05
Title
Finisher communication error 3
Description A large amount of data from the Finisher causes the reception
buffer overflow
Remedy
Turn OFF and then ON the main power
E713 0004 05
Title
Finisher communication error 4
Description OFF detection of detect signal
Remedy
Turn OFF and then ON the main power
E713 0005 05
Title
Finisher communication error 5
Description (1) Fails to receive the signal although retransmission is
executed for 3 times.
(2) This error occurs also when the Finisher is removed.
* Detection description (2) occurs only in the case of Cont
v28.30/Dcon v54.02 or earlier.
Remedy
Turn OFF and then ON the main power
E713 0006 05
Title
Finisher communication error 6
Description NACK reception for 3 times straight
Remedy
Turn OFF and then ON the main power
E713 0007 05
Title
Finisher communication error 7
Description Overflow of driver buffer due to many requests from the upper
task before the process of the driver
Remedy
Turn OFF and then ON the main power
