Buderus Logano G225 Скачать руководство пользователя страница 9

Страница: 9 / 60

Product details

Logano G225/Logano plus GB225 - We reserve the right to make any changes due to technical modifications.

2.9

Contents

Upon delivery, check that the packaging is
undamaged.

Check that all components have been delivered.

Boiler as assembled block

Boiler supplied in sections

Component

Quan-

tity

Packaging

Boiler block

1 pallet

Boiler casing

1 box

Thermal insulation

1 shrink-
wrapped pack

Burner, burner hood,
burner door and fixings

technical documentation
for burner and boiler.

1) The adjustable feet are packed with the burner hood

1 box

Control unit, technical
documentation for
controller

1 box

Tab. 1

Contents

Component

Quan-

tity

Packaging

Front and rear boiler sec-
tions

1 pallet

Centre sections

loose

Furniture

1 box

Boiler casing

1 box

Thermal insulation

1 shrink-
wrapped pack

Burner, burner hood,
burner door and fixings

technical documentation
for burner and boiler.

1) The adjustable feet are packed with the burner hood

1 box

Control unit, technical
documentation for
controller

1 box

Tab. 2

Contents

Содержание Logano G225





























































Результаты поиска

Содержание Logano G225

Отзывы:

Похожие инструкции для Logano G225

Бренды по названию

Популярные бренды

Buderus Logano G225, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Logano G225

Отзывы:

Похожие инструкции для Logano G225

Бренды по названию

Популярные бренды