Buderus Logano G225 Скачать руководство пользователя страница 13

Страница: 13 / 60

Product details

Logano G225/Logano plus GB225 - We reserve the right to make any changes due to technical modifications.

2.10.5 Conditions for the power supply

2.10.6 Conditions for the system configuration and water quality

Operating conditions

Notes – detailed requirements

Supply voltage

195 – 253 V

The outer casing/boiler must be earthed for safety reasons and to function correctly.

Fuse

10 A

Frequency

47.5 – 52.5 Hz

Sine wave

Enclosure rating

−

IP40 (protected against penetration by foreign bodies > 1 mm dia., not protected against
water ingress)

Tab. 9

Mains power supply

Operating conditions

Notes – detailed requirements

Operating pressure (above
atmospheric)

0.5 – 4.0 bar

Permissible testing pressure

1.0 – 5.2 bar

Protection against excess
temperatures via TR thermostat

50 – 90 °C

Protection against excess
temperatures via STB high limit
safety cut-out

100 °C

Water quality

−

The heating system may only be filled and topped up with water of domestic water quality.
We recommend a pH value of 8.2 – 9.5.

Tab. 10 System configuration and water quality

Содержание Logano G225





























































Результаты поиска

Содержание Logano G225

Отзывы:

Похожие инструкции для Logano G225

Бренды по названию

Популярные бренды

Buderus Logano G225, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Logano G225

Отзывы:

Похожие инструкции для Logano G225

Бренды по названию

Популярные бренды