Buderus Logano G215 WS Скачать руководство пользователя страница 36

Страница: 36 / 62

Boiler installation

Logano G215 WS - We reserve the right to make any changes due to technical modifications.

8.2

Making the water connections

8.2.1 Connecting central heating flow and return

Connect the central heating return to connector RK.

Connect the central heating flow to connector VK.

8.2.2 Connecting the safety flow and return

We recommend the connection of a boiler safety set
(accessory) or an air-vent valve (accessory) to
connector VSL.

8.2.3 DHW cylinder connection

Connect the DHW cylinder return to connector RS.

Connect the DHW cylinder flow either at VS1 or VS2.

Seal off the surplus VS connector.

CAUTION!

SYSTEM DAMAGE

through leaking connections.

Connect the pipes without stress to the
boiler connections.

Fig. 52 Connecting the heating flow and return

USER NOTE

We recommend the on-site installation of a
dirt trap (accessory) into the central
heating return to prevent contamination on
the water side.

VSL:

Flow safety line

VK:

Boiler flow

RK:

Boiler return

VS:

DHW cylinder flow

RS:

DHW cylinder return

EL:

Drain

Fig. 53 Connecting the air vent valve to the safety flow

VSL

CAUTION!

SYSTEM DAMAGE

through the connection of incorrect
components to connector VSL.

Never connect a summer line, DHW
cylinder or another heating circuit to
VSL.

Fig. 54 DHW cylinder, connecting

RS2

RS1

VS1

VS2

Содержание Logano G215 WS































































Результаты поиска

Содержание Logano G215 WS

Отзывы:

Похожие инструкции для Logano G215 WS

Бренды по названию

Популярные бренды

Buderus Logano G215 WS, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Logano G215 WS

Отзывы:

Похожие инструкции для Logano G215 WS

Бренды по названию

Популярные бренды